印刷机械 上光机检测

GB/T 28386-2012印刷、纸加工、造纸机械和辅助设备的噪声测量方法.准确度等级2和3

本标准规定了在指定的测量条件下测定、标示、验证GB/T 28387所涉及的印刷、纸加工机械及EN 1034所涉及的造纸、装订整饰机械的空气噪声发射值的要求；还规定了本标准所采用的噪声测量方法及测试时的安装和运行条件。本标准适用于上述机械（例如：在附录A～附录I中列出的机器和机器部件）的噪声发射的测定、标示和验证。测试报告中建议记录测量噪声时与装配、安装和运行条件及工作位置的安排有关的所有信息。噪声发射值包括工作位置的发射声压级L<下标p>和机器的声功率级L<下标w>.本标准指定的噪声测量方法包括工程法（准确度2级）和简易法（准确度3级）。使用本标准进行噪声发射值的测定将确保其在特定范围内的可重复性。这些范围由采用的噪声测量方法的精度等级来确定。测量工作位置和其他指定位置的发射声压级由基础标准（EN ISO 11200:1995、EN ISO 11202：1995、EN ISO 11203：1995和EN ISO 11204：1995）来确立，声功率级的测量由基础标准（EN ISO 3740：2000、EN ISO 3744：1995、EN ISO 3746：1995、EN ISO 9614-1：1995和EN ISO 9614-2：1996）来确立。

GB/T 28387.1-2012印刷机械和纸加工机械的设计及结构安全规则.第1部分：一般要求

GB/T 28387的本部分规定了各种印刷、纸加工机械和相关一般设备的安全要求，并应与GB/T 28387-2012中的其他各部分一起使用。GB/T 28387.2-2012～GB/T 28387.5-2012中的特殊要求优先于GB/T 28387.1-2012中的相应要求。本部分涉及在制造商有意的和预知的状态下，使用印刷机械和纸加工机械所有的常见重大危险。（见第4章）。本部分适用于：纸张印刷或类似材料印刷的印刷机械，包括丝网印刷机械；印刷过程中的准备机械和印刷机械的辅助设备也被视为印刷机械、纸张、印品、印版和油墨（印刷前后）处理的机械，还适用于印刷清洗、质量检查等机械（辅助印刷机械）。纸加工机械，即纸张、纸板及类似材料的处理、加工或制成品的机械。

GB/T 28387.2-2012印刷机械和纸加工机械的设计及结构安全规则.第2部分：印刷机、上光机和印前机械

GB/T 28387的本部分规定了印刷机、上光机和印前机械及辅助设备的安全要求，本部分应与GB/T 28387.1-2012一起使用，以共同确定在按制造商预定的条件下使用印刷机、上光机和印前机械及辅助设备时的所有重大危险（见第4章）。本部分未涉及由机器的噪声所引发的危险。这些危险基本包括在GB/T 28387.1-2012中。本部分适用于：——印前机械（用于生产原稿和印版的机械和装置）；用于生产胶片和印版的曝光设备；用于胶片和印版显影的设备；用于清洗印版的机器；用于折弯印版的机器；用于胶片和印版打孔的机器；用于裁切胶片和印版的机器；用于生产凹印版材的机器；扫描仪。——印刷机和上光机：打样机；单张纸印刷机和上光机，包括数字印刷机；卷筒纸平板印刷机和上光机，包括数字印刷机；丝网印刷机。辅助设备：滚筒和辊子清洗装置；连续工作的烘干装置；喷粉装置；供墨和润湿装置的辅助装置；自动夹紧印版装置；印版、辊子和刮墨刀清洗设备；纸堆翻转机；测量和控制装置。本部分不适用于承印物为纺织物的高压清理装置和丝网印刷机。

GB/T 28387.4-2012印刷机械和纸加工机械的设计及结构安全规则.第4部分：书籍装订、纸加工和整饰机械

GB/T 28387的本部分规定了书籍装订、纸加工和整饰机械的安全要求，本部分应与GB/T 28387.1-2012一起使用，以共同确定在按制造商预定的条件下使用书籍装订、纸加工和整饰机械时的所有重大危险（见第4章）。本部分中的特殊要求优先于GB/T 28387.1-2012中的相应要求。本部分未涉及由机器的噪声所引发的危险。这些危险基本包括在GB/T 28387.1-2012中，但本部分规定了像折页机、生产信封机和卫生产品机的一些降噪措施。本部分适用于：——书籍装订机械：订书、铆钉、打眼机和装订机；骑马订书机；配页机；无线胶订机；打孔机；书芯压平机；压书机；单张纸折页机；书籍生产线；书芯扒圆起脊机；书背加衬上堵头机；上封皮机；封皮压痕成型机。——纸加工机械：信封机；卫生产品生产机；插页机；计数堆积机；纸张压痕机。——纸张整饰机械：涂布机；复合机。复合机。

GB/T 28387.5-2012印刷机械和纸加工机械的设计及结构安全规则.第5部分：瓦楞纸板生产机械以及纸板和瓦楞纸板加工设备

GB/T 28387的本部分规定了瓦楞纸板生产机械以及纸板和瓦楞纸板加工设备的安全要求，本部分应与GB/T 28387.1-2012一起使用，以共同确定在按制造商预定的条件下使用瓦楞纸板生产机械及纸板和瓦楞纸板加工设备时的所有重大危险（见第4章）。本部分中的特殊要求优先于GB/T 28387.1-2012中的相应要求。本部分未涉及由机器的噪声所引发的危险。这些危险基本包括在GB/T 28387.1-2012中，但本部分规定了瓦楞纸板生产机械、加工设备和平压模切机的降噪要求。本部分适用于瓦楞纸板生产机械以及纸板和瓦楞纸板加工设备；——瓦楞纸板生产机械；——粘箱机；——印刷开槽机，圆压圆模切机与其组合机（联机）；——手工给纸平压模切压痕机；——自动给纸平压模切压痕机；——管式缠绕机。

JB/T 3090-2010印刷机械产品命名与型号编制方法

本标准规定了印刷机械产品命名与型号编制方法的产品的命名、型号编制方法。本标准适用于制版设备、装订设备、裁切设备、表面整饰与包装设备、配套辅助设备等产品，不适用于印刷机。对于本标准未涵盖的印刷机械的产品应参照执行。

JB/T 4178-2016印刷机术语

本标准规定了各类印刷机及其主要结构部件以及与印刷机质量相关的技术参数的基本术语和定义，以保证在生产、教学和学术等活动中正确应用概念。本标准适用于在印刷机械或相关编写标准、出版、教学及国内外技术交流中使用。

JB/T 8586-2010印刷机械 上光机

本标准规定了上光机的术语和定义、型式、基本参数、型号和名称、要求、试验方法、检验规则、标志、包装、运输与贮存。本标准适用于单张纸紫外线固化和红外线干燥的涂布上光机。本标准不适用于局部上光机。

JB/T 9111-2014不干胶标签印刷机

本标准规定了不干胶标签印刷机的术语和定义、型式与基本参数、要求、试验方法、检验规则、标志、包装、运输与贮存。本标准适用于对各种卷筒不干胶材料进行印刷的、以感光树脂版或PS版为版材的卷筒料不干胶标签印刷机。本标准还适用于联线烫印、覆膜、模切、上光等功能单元的卷筒料不干胶标签印刷机(以下简称标签印刷机)。

JB/T 11122-2010印刷机械 局部上光机

本标准规定了局部上光机(以下简称上光机）的术语和定义、型式、型号与基本参数、要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于单张纸紫外线固化和红外线干燥的局部涂布上光机。

JB/T 11947-2014印刷机械 印后设备类别划分

本标准规定了印刷机械用印后设备的术语和定义、类别划分原则及各类别设备的划分。本标准适用于印刷机械用装订设备、表面整饰设备和成型加工设备的分类。

JB/T 11948-2014印刷机械 印后机械基本术语

本标准规定了印刷机械用印后机械的产品名称及其主要结构部件的基本术语,以保证在生产、教学和学术等活动中正确应用概念。本标准适用于印刷机械行业及相关编写标准、出版、教学、科研及国内外技术交流中使用。

EN 1010-3-2002机械安全.印刷和纸加工机械的设计和施工的安全要求.第3部分:切削机.包含修改件A1-2009

This European Standard applies to cutting machines used in paper converting:guillotines; three-knife trimmers; index cutting machines; trimmers; rotary cutters; round cornering machines; label punching machines. This European Standard is only applicable in conjunction with EN 1010-1:2004+A1. Both parts together identify all significant hazards relevant to the cutting machines when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). The specific requirements of This European Standard take precedence over respective requirements of EN 1010-1:2004+A1. This European Standard is not applicable to cutting machines manufactured before the publication of This European Standard by CEN. This standard does not apply to winder-slitters or sheeters (see EN 1034-1, EN 1034-3, prEN 1034-5).

EN 1010-4-2004机械安全.印刷和纸加工机械的设计和施工的安全要求.第4部分:装订机,纸加工机和修整机.包含修改件A1-2009

This document applies to bookbinding machines: stitching; riveting; eyeletting and attaching machines; gang stitchers; gathering machines; perfect binders; paper drills; book signature presses; book presses; sheet folding machines; book production lines for the production of books with hard covers; back rounding and pressing machines; backlining and head banding machines; casing-in machines; book cover crease forming machines. paper converting machines: machines for the production of envelopes; machines for the production of sanitary items; inserting machines; counter-stackers; paper embossing machines. paper finishing machines: coaters; laminators.This document shall be used together with "EN 1010-1:2004+A1". Both parts together identify all significant hazards relevant to bookbinding; paper converting and paper finishing machines when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). The specific requirements in EN 1010-4 take precedence over respective requirements in "EN 1010-1:2004+A1".This document does not deal with risks generated by noise emitted from the machines. These issues are covered basically in "EN 1010-1:2004+A1". However; for machines like sheet folding machines and machines for the production of envelopes and sanitary items; some specific proposals for noise reduction measures are given.This document is not applicable to bookbinding; paper converting and finishing machines manufactured before the date of publication of this document by CEN.

EN 1034-1-2000机械安全.造纸机械和精整机的设计和建造安全要求.第1部分:通用要求.包含修改件A1-2010

This standard applies to paper making and paper finishing machines. It contains definitions and requirements which apply to all paper making and paper finishing machines listed in annex A and shall be used in connection with the specific part applicable for the respective machine listed in annex A. Specific parts can contain additional requirements or deviations from EN 1034-1 in which case the specific stipulations take precedence over the specification made in EN 1034-1. The standard deals with the hazards listed in 4.This standard does not apply to machines used in paper converting. See EN 1010-1 to EN 1010-5.This standard applies to machines produced after............. (date of CEN approval).

EN 13023-2003印刷,纸张吹炼,造纸机械及附属设备的噪声测量法.2类和3类准确度;包含修改件A1-2010

This standard specifies all the information necessary to carry out efficiently and under standardized conditions the determination, declaration and verification of airborne noise emission from printing and paper converting machines covered by the EN 1010 series and from paper making and finishing machines covered by the EN 1034 series. It specifies noise measurement methods and installation and operating conditions to be used for the test.This standard applies to those machines listed in the normative annexes A to J. The principles of this noise test code should be applied as far as possible also for the determination of noise emission of machines and machine parts not listed in the normative annexes A to J. In such cases, all information relating to assembly, installation and operating conditions as well as the arrangement of work stations should be recorded and reported in the test report. Noise emission characteristics include emission sound pressure levels at work stations and the sound power level. Declared noise emission values permit comparison of printing and paper machines on the market. The use of this noise test code ensures the reproducibility of the determination of the characteristic noise emissions within specific limits. These limits are determined by the accuracy grade of the noise measuring method used. Noise measurements specified byThis standard are carried out by the engineering method (accuracy grade 2) and the survey method (accuracy grade 3).

BS EN 1010-2-2006+A1-2010机械安全性.印刷机和换纸机的设计和构造的安全性要求.包括预压机械的印刷机和涂漆机

This document applies to: Pre-press machinery (machinery and devices for the production of master copies and printing forms): exposure equipment for the production of films and printing forms; equipment for developing films and printing forms; washing machines for printing forms; machines for bending printing forms; punching machines for film and printing forms; cutting machines for film and printing forms; machines for the production of gravure printing forms; scanners. Printing and varnishing machines: proofing presses; sheet-fed printing presses and varnishing machines including digital printing presses; web-fed rotary presses and varnishing machines including digital printing presses; screen printing presses. Auxiliary devices: cylinder and roller washing devices; continuous flow drying devices; powder spraying devices; auxiliary devices on inking and damping units; automatic plate clamping devices; washing equipment for printing forms, rollers and scrapers; pile turners; measuring and control devices.This document shall be used together with !EN 1010-1:2004+A1". Both parts together identify allsignificant hazards relevant to printing and varnishing machines including pre-press machinery and auxiliary devices, when they are used as intended and under the conditions foreseen by the manufacturer (see clause4). The specific requirements specified in prEN 1010-2 take precedence over respective requirements in thisstandard.This document does not deal with risks generated by noise emitted from the machines. These issues arefundamentally covered in !EN 1010-1:2004+A1"This document does not apply to high-pressure cleaning devices and screen printing presses for textilesubstrates.This document is not applicable to printing and varnishing machines including pre-press machinery which aremanufactured before the date of publication of this document by CEN.

BS EN 1010-3-2002+A1-2009机械安全性.印刷和纸加工机械的设计和制造的安全性要求.切纸机

1.1 This European Standard applies to cutting machines used in paper converting:- guillotines;- three-knife trimmers;- index cutting machines;- trimmers;- rotary cutters;- round cornering machines;- label punching machines.This European Standard is only applicable in conjunction with !EN 1010-1:2004+A1". Both parts togetheridentify all significant hazards relevant to the cutting machines when they are used as intended and under theconditions foreseen by the manufacturer (see Clause 4). The specific requirements of this European Standard takeprecedence over respective requirements of !EN 1010-1:2004+A1".This European Standard is not applicable to cutting machines manufactured before the publication of this EuropeanStandard by CEN.1.2 This standard does not apply to winder-slitters or sheeters (see EN 1034-1, EN 1034-3, prEN1034-5).