圆柱形 复合罐检测
GB/T 4122.4-2010包装术语 第4部分：材料与容器
GB/T 4122的本部分规定了包装用材料及容器的术语及定义。本部分适用于包装及与包装相关的领域。
GB/T 10440-2008圆柱形复合罐
本标准规定了圆柱形复合罐（以下简称复合罐）分类、要求、试验方法、检验规则及标志、包装、运输、和贮存。本标准适用于主要采用纸板和纸、塑、铝等组成的复合材料制成罐身，且一端已有端盖密封的圆柱形小型包装容器。
GB/T 21709.5-2008针灸技术操作规范.第5部分:拔罐
GB/T 21709的本部分规定了拔罐的术语和定义、操作步骤与要求、注意事项与禁忌。本标准适用于拔罐技术操作。
GB/T 28119-2011食品包装用纸、纸板及纸制品.术语
本标准规定了食品包装用纸、纸板及纸制品的相关术语。本标准适用于所有食品包装用纸、纸板及纸制品。
GB 50915-2013有色金属矿山井巷工程设计规范
本规范适用于有色金属矿山井巷工程的设计。
UL 1746-2007钢制地下储罐用外部防腐蚀系统
These requirements cover preengineered corrosion protection systems. Part i covers factory-installed galvanic-type cathodic protection. Part ii covers factory assembled composite systems. Part iii covers factory assembled jacket systems. Part iv covers factory assembled coated systems. These corrosion protection systems are intended to be completely installed at the factory on carbon steel underground storage tanks. Part ii of this standard covers fiberglass reinforced plastic (FRP), materials only. Part iii of this standard covers FRP, polyurethane, polyurea and high density polyethylene (HDPE) materials only. Part iv covers polyurethane materials only. These corrosion protection systems are intended to be installed, operated and maintained in accordance with the manufacturer's instructions.
BS EN 14620-1-2006工作温度0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制造的设计和生产.总则
This European Standard is a specification for vertical, cylindrical tanks, built on site, above groundand of which the primary liquid container is made of steel. The secondary container, if applicable, maybe of steel or of concrete or a combination of both. An inner tank made only of pre-stressed concreteis excluded from the scope of this European Standard.This European Standard specifies principles and application rules for the structural design of the“containment” during construction, testing, commissioning, operation (accidental included), anddecommissioning. It does not address the requirements for ancillary equipment such as pumps,pumpwells, valves, piping, instrumentation, staircases etc. unless they can affect the structural designof the tank.This European Standard applies to storage tanks designed to store products, having an atmospheric boiling point below ambient temperature, in a dual phase, i.e. liquid and vapour. The equilibrium between liquid and vapour phases being maintained by cooling down the product to a temperature equal to, or just below, its atmospheric boiling point in combination with a slight overpressure in the storage tank.The maximum design pressure of the tanks covered by this European Standard is limited to 500 mbar. For higher pressures, reference can be made to EN 13445, Parts 1 to 5.The operating range of the gasses to be stored is between 0 °C and –165 °C. The tanks for the storage of liquefied oxygen, nitrogen and argon are excluded.The tanks are used to store large volumes of hydrocarbon products and ammonia with low temperature boiling points, generally called “Refrigerated Liquefied Gases” (RLG’s). Typical products stored in the tanks are: methane, ethane, propane, butane, ethylene, propylene, butadiene (this rangeincludes the LNG’s and LPG’s).NOTE Properties of the gases are given in Annex A.The requirements of this European Standard cannot cover all details of design and construction because of the variety of sizes and configurations that may be employed. Where complete requirements for a specific design are not provided, the intention is for the designer, subject to approval of the purchaser's authorized representative, to provide design and details that are as safeas those laid out in this European Standard.This European Standard specifies general requirements for the tank concept, selection and general design considerations.
