全无油润滑高压往复活塞氧气压缩机检测

全无油润滑高压往复活塞氧气压缩机检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB 50771-2012有色金属采矿设计规范

本规范适用于新建、改建、扩建的有色金属矿山预可行性研究、可行性研究和矿山工程建设的采矿设计。

MT/T 1097-2008煤矿机电设备检修技术规范

本规范为企业的设备检修提供指导意见,可作为企业制定设备检修细则、检修操作规程和设备完好标准的依据。本规范执行《煤炭法》、《矿山安全法》、《煤矿安全监察条例》、《煤矿安全规程》等煤炭法律、法规、规程和管理标准,执行和有关煤炭行业的所有技术标准。本规范通用部分的技术要求和计量单位等执行或有关行业的技术标准。

JGJ 33-2012建筑机械使用安全技术规程

本规程适用于建筑施工中各类建筑机械的使用与管理。

JGJ 160-2016施工现场机械设备检查技术规范

本规范适用于新建、扩建和改建的工业与民用建筑及市政工程施工现场机械设备的检查。

JB/T 12950-2016全无油润滑高压往复活塞氧气压缩机

本标准规定了全无油润滑高压往复活塞氧气压缩机(以下简称氧压机)的基本参数、技术要求、试验方法、检验规则、标志、包装和贮存。本标准适用于进气压力为0.002 MPa~0.4 MPa、额定排气压力为15.0 MPa、公称容积流量不大于100 m<上标3>/h(标准状态)的氧压机。不在本标准范围内的氧压机，可参照本标准执行。

DL/T 774-2015火力发电厂热工自动化系统检修运行维护规程

本标准规定了火力发电厂热控系统检修运行维护的内容、方法和技术管理应达到的标准。本标准适用于火力发电厂已投产机组热控系统的检修和日常运行维护工作。

DB64/ 558-2009建筑工人安全操作规程

本标准规定了建筑工人安全操作的术语和定义、总则、一般规定、架子工、瓦工、抹灰工、石工、木工、钢筋工、混凝土工、普通工、电工、安装电工、防水工、起重吊装工、金属焊割作业工、油漆工、测量工、机械设备维修工、水暖工、铆工、通风工、筑炉工、保温工、桩基施工、大模片施工、钢结构及网架施工、装饰装修施工、拆除施工、土方及筑路机械、桩工机械、吊装及垂直运输机械、混凝土机械、中小型施工机具、市政工程的操作。

DIN EN 1012-3-2014压缩机和真空泵. 安全要求. 第3部分:加工压缩机; 德文版本EN 1012-3-2013

This part of EN 1012 is applicable to compressors having an operating pressure greater than 0,5 bar and designed to utilise all gases other than air, nitrogen or inert gases which are covered in part 1. The standard lists the significant hazards associated with compressors and specifies safety requirements applicable to the design, installation, operation, maintenance and dismantling of compressors during their foreseeable lifetime and subsequent disposal.This part of EN 1012 includes under the general term compressors, those machines which comprise;- the compressor itself- a prime mover- any component or device supplied which is necessary for safe operation of the compressor.In addition it applies to partly completed compressors having a compressor in combination with some of these components as well as compressor assemblies operating in combination.Excluded are refrigerant compressors used in refrigerating systems or heat pumps as defined in EN 378-1.

DIN EN 12583-2014天然气基础设施.压缩机泵站.功能要求

This European Standard describes the specific functional requirements for the design, construction, operation, maintenance and disposal activities for safe and secure gas compressor stations. This European Standard applies to new gas compressor stations with a Maximum Operating Pressure (MOP) over 16 bar and with a total shaft power over 1 MW. For existing compressor stations, this European Standard applies to new compressor units. Where changes/modifications to existing installations take place, due account may be taken of the requirements of this European Standard. This European Standard does not apply to gas compressor stations operating prior to the publication of this European Standard. The purpose of this European Standard is intended to: - ensure the health and safety of the public and all site personnel, - to cover environmental issues and - to avoid incidental damage to nearby property. This European Standard specifies common basic principles for the gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or codes of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles. In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts). CEN/TR 13737 (all parts) gives: - clarification of all legislations/regulations applicable in a member state; - if appropriate, more restrictive national requirements; - a national contact point for the latest information. This European Standard does not apply to: - off-shore gas compressor stations; - gas compressor stations for compressed natural gas filling-stations; - customer installations downstream of the point of custody trans

BS 6739-2009过程控制系统仪表的实施规范:安装设计和实施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.