家用和类似用途前置过滤器检测

GB 4706.93-2008家用和类似用途电器的安全.工业和商业用湿式和干式真空吸尘器的特殊要求

GB 4706.1-2005的该章用下述内容代替:GB 4706的本部分适用于由电机驱动的工业和商业用真空吸尘器的安全，这些器具包括带有或不带附件的湿式、干式或湿干兼有的便携式器具和驻立式器具。例如从工作台和机器上抽吸的灰尘或类似污物。其单相器具额定电压不超过250V，其他器具额定电压不超过480V。本部分也适用于收集有危险的灰尘器具，有危险的灰尘包括石棉，或附加要求使用的液体。本部分也适用于除电动机以外其他驱动形式的器具，但必须考虑其作用。对于电池供电的器具应参考IEC 60355-2-72.

CJJ/T 116-2014建设领域应用软件测评工作通用规范

本规范适用于建设领域应用软件，包括城乡规划应用软件、城乡建设应用软件、建筑工程应用软件、住房与房地产应用软件和信息技术综合应用软件的测评。

QB/T 4695-2014家用和类似用途前置过滤器

本标准规定了用于去除自来水中颗粒状物质的家用和类似用途过滤装置的术语和定义、产品分类与型号命名、要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于以市政自来水或其他集中式供水为原水,以过滤网或者叠片为主要过滤手段,供家庭和类似场所使用的前置过滤器。

QB/T 4990-2016家用和类似用途中央净水设备

本标准规定了家用和类似用途中央净水设备(以下简称“中央净水设备”)的术语和定义、分类与命名、要求、试验方法、检验规则和标志、包装、运输、贮存。本标准适用于以市政自来水或其他集中式供水为原水，具备冲洗功能，供家庭或类似场合集中处理、改善水质的水处理设备。

ITU-T G.9954-2007家庭网络收发器.增强物理、媒体接入和链路层规范研究组15

This Recommendation specifies the interoperability and compatibility for G.9954v2 stations. Therequirements are written from the perspective of a compliant transmitter, although some minimumperformance requirements are established for receivers. This Recommendation does not specifyimplementation.A G.9954v2 station at a minimum shall be capable of transmitting and receiving over phoneline orover coax.The structure of this Recommendation is as follows:Clause 6: PHY layer specification over phoneline – This clause specifies the G.9954v2 PHYlayer specification over phoneline.Clause 7: PHY layer specification over coax – This clause specifies the G.9954v2 PHY layerspecification over coax.Clause 8: Media access protocol specification – This clause specifies the G.9954v2 media accessprotocol.Clause 9: Compatibility specification – This clause describes the method by which backwardscompatibility, coexistence and interoperability with G.9954 nodes is achieved in a mixed networkof G.9954v2 and G.9954v1 nodes.Clause 10: Quality of service – This clause describes the G.9954v2 quality of service framework.Clause 11: Link-layer protocol specification – This clause specifies the required link layer controlfunctionalities.

DIN EN 13278-2014前开式独置燃气加热器.德文版本EN 13278-2013

This European Standard specifies the requirements and test methods for the construction, safety, marking and rational use of energy of open fronted gas-fired independent space heaters with and without a fan to assist with the transportation of flue gases. Although the fan may be mounted outdoors, this standard only covers appliances where the body of the appliance is indoors. This standard applies to types B11AS, B11BS, B14AS, and B14BS open fronted gas-fired independent space heating appliances that incorporate an atmospheric burner, that are connected directly to an open flue or to a device to evacuate the products of combustion (open-flued appliances), that have a nominal heat input not exceeding 20 kW (based on the net calorific value) and that are delivered with the gas-carrying components, burner (s), combustion chamber and heat exchanger fully assembled.

DIN EN 14829-2007不超过6kW的普通供热用独立式燃气无烟筒对流加热器

This document specifies, for the purpose of type examination, the requirements and test methods for construction, safety, marking and rational use of energy of 2ne and 3rd family gas-fired domestic flueless space heating appliances having a nominal input not exceeding 6 kW (based on net calorific value). It covers the following Type AAS fixed flueless heaters: NOTE These are type A appliances fitted with an atmosphere sensing device, with or without a fan. a) heaters with or without a catalytic converter; b) Category 1 appliances burning gases of the second family; c) Category 2 appliances burning gases of the second and third families. It does not cover qi. Mobile heaters.ii. Category 1 appliances burning gases of the third family.iii. Portable flueless heaters.iv. Diffusive catalytic combustion heaters. There are no specific thermal efficiency requirements appropriate to these types of appliance as: -- All the heat produced by the combustion process is released into the space to be heated. -- The requirements with regard to the combustion performance, which is a safety matter, ensure the effective burning of the fuel gas. This standard is only applicable to appliances which are to be type tested. Matters related to quality assurance systems, tests during production and to certificates of conformity of auxiliary devices are not dealt with by this standard.

DIN EN 15429-3-2015扫路机. 第3部分: 颗粒物收集效率. 试验和评估; 德文版本EN 15429-3-2015

This document applies to surface cleaning machines for outdoor applications in public areas, roads, airports and industrial complexes. Cleaning machines for winter maintenance and/or indoor applications are not included within the scope of this European Standard. Surface cleaning machines in terms of this Standard, are self-propelled, truck mounted, attached sweeping equipment or pedestrian controlled as disclosed in EN15429-1. Surface cleaning machines by way of their function, have to scarify and effect movement of the material to be collected by; brushes and/or similar to a collection mechanism and thence conveyed to a hopper. Surface cleaning machines are additionally equipped with means to suppress emission of airborne matter. This standard defines a test apparatus/method to measure the efficiency of the collection of particulate matter when the surface cleaning machine is used as intended and under the conditions foreseen by the manufacturer. This standard discloses a method to declare a uniform expression of the result. Emissions from motive prime-movers are included in the test method. This document does not apply to road surface cleaning equipment that would be front mounted on tractors according to prEN 13524, or other vehicles. This standard does not apply to machines or components that are specifically designed for cleaning tramlines and rail tracks. This standard applies to machines manufactured after the approval date of the standard by CEN. Industrial sweepers, within the scope of EN 60335-2-72 are excluded from this standard.

DIN EN 16191-2014隧道机械. 安全要求; 德文版本EN 16191-2014

This European Standard is applicable to tunnelling machinery as defined in Clause 3 used for the construction of tunnels, shafts and other underground excavations. It deals with all significant hazards, hazardous situations and events relevant to such machinery when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard covers monitoring for hazardous atmospheres within the confines of the tunnelling machinery. Hand-arm and whole-body vibration are not considered as significant hazard for tunnelling machinery. The following items and applications are not covered by this European Standard: - the additional requirements for the use of tunnelling machinery under hyperbaric conditions; - the additional requirements for use of tunnelling machinery in potentially explosive atmospheres; NOTE For the application in potentially explosive atmospheres see EN 1710:2005+A1:2008 for guidance. - ancillary tools and equipment which are not an integral part of the tunnelling machinery but used on or with the machinery; - services (e. g. power supply, water, pipes, compressed air, etc.) supplied to the tunnelling machinery; - loading and transport equipment which is not an integral part of the tunnelling machinery, e. g. man riders, locomotives, grout cars, segment cars, muck cars and shaft hoisting equipment. This European Standard is not applicable to road headers, continuous miners and impact rippers.

BS 6739-2009过程控制系统仪表的实施规范:安装设计和实施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

BS EN 14829-2007家用燃气标定热负荷不超过6kW的无烟道单独采暖炉

This document specifies, for the purpose of type examination, the requirements and test methods forconstruction, safety, marking and rational use of energy of 2nd and 3rd family gas-fired domesticflueless space heating appliances having a nominal input not exceeding 6 kW (based on net calorificvalue).It covers the following Type AAS fixed flueless heaters:NOTE These are type A appliances fitted with an atmosphere sensing device, with or without a fan.a) heaters with or without a catalytic converter;b) Category 1 appliances burning gases of the second family;c) Category 2 appliances burning gases of the second and third families.It does not coveri. Mobile heaters.ii. Category 1 appliances burning gases of the third family.iii. Portable flueless heaters.iv. Diffusive catalytic combustion heaters.There are no specific thermal efficiency requirements appropriate to these types of appliance as: All the heat produced by the combustion process is released into the space to be heated. The requirements with regard to the combustion performance, which is a safety matter, ensure theeffective burning of the fuel gas.This standard is only applicable to appliances which are to be type tested. Matters related to qualityassurance systems, tests during production and to certificates of conformity of auxiliary devices arenot dealt with by this standard.

BS EN 55016-2-2-2011无线电干扰和抗扰度测量设备和测量方法规范.干扰和抗扰度测量方法.干扰功率的测量

This part of CISPR 16 specifies the methods of measurement of disturbance power using theabsorbing clamp in the frequency range 30 MHz to 1 000 MHz.NOTE In accordance with IEC Guide 107, CISPR 16-2-2 is a basic EMC publication for use by productcommittees of the IEC. As stated in Guide 107, product committees are responsible for determining theapplicability of the EMC standard. CISPR and its sub-committees are prepared to co-operate with productcommittees in the determination of the value of particular EMC tests for specific products.

BS EN ISO 11201-2010声学.机器和设备发射的噪声.在一个反射平面上方可忽略环境校正条件下进行工作位置和其他指定位置的发射声压级测量

This International Standard specifies a method for determining the emission sound pressure levels ofmachinery or equipment, at a work station and at other specified positions nearby, in an essentially free fieldover a reflecting plane. A work station is occupied by an operator and may be located in open space, in theroom where the source under test operates, in a cab fixed to the source under test, or in an enclosure remotefrom the source under test. One or more specified positions may be located in the vicinity of a work station, orin the vicinity of an attended or unattended machine. Such positions are sometimes referred to as bystanderpositions.Emission sound pressure levels are determined as A-weighted levels. Additionally, levels in frequency bandsand C-weighted peak emission sound pressure levels can be determined in accordance with this InternationalStandard, if required.NOTE 1 The contents of the series ISO 11200 to ISO 11205 are summarized in ISO 11200.With the method specified in this International Standard, results of accuracy grade 1 (precision grade) oraccuracy grade 2 (engineering grade) are obtained. Corrections are applied for background noise, but not forthe acoustic environment. Instructions are given for the mounting and operation of the source under test andfor the choice of microphone positions for the work station and for other specified positions. One purpose ofthe measurements is to permit comparison of the performance of different units of a given family of machines,under defined environmental conditions and standardized mounting and operating conditions.NOTE 2 The data obtained can also be used for the declaration and verification of emission sound pressure levels asspecified in ISO 4871

BS EN ISO 11204-2010声学.机械装置及设备发出的噪声.用精确环境修正测定工作地点和其它试验场所声压级

This International Standard specifies a method for determining the emission sound pressure levels ofmachinery or equipment, at a work station and at other specified positions nearby, in any environment whichmeets certain qualification requirements. A work station is occupied by an operator and may be located inopen space, in the room where the source under test operates, in a cab fixed to the source under test, or in anenclosure remote from the source under test. One or more specified positions may be located in the vicinity ofa work station, or in the vicinity of an attended or unattended machine. Such positions are sometimes referredto as bystander positions.Emission sound pressure levels are determined as A-weighted levels. Additionally, levels in frequency bandsand C-weighted peak emission sound pressure levels can be determined in accordance with this InternationalStandard, if required.NOTE 1 The contents of the series ISO 11200 to ISO 11205 are summarized in ISO 11200.A method is given for determining a local environmental correction (subject to a specified limiting maximumvalue) to be applied to the measured sound pressure levels to exclude the effects of reflections from reflectingsurfaces other than the plane on which the source under test is placed. This correction is based upon themean sound pressure level on a measurement surface, the sound pressure level measured at a specifiedposition, and either an environmental correction or the equivalent absorption area of the test room.With the method specified in this International Standard, results of accuracy grade 2 (engineering grade) oraccuracy grade 3 (survey grade) are obtained. Corrections are applied for background noise and, asdescribed above, for the acoustic environment. Instructions are given for the mounting and operation of thesource under test and for the choice of microphone positions for the work station and for other specifiedpositions. One purpose of the measurements is to permit comparison of the performance of different units of agiven family of machines, under defined environmental conditions and standardized mounting and operatingconditions.NOTE 2 The data obtained can also be used for the declaration and verification of emission sound pressure levels asspecified in ISO 4871.

ANSI C63.4-20099 kHz至40 kHz范围内低压电气设备和电子设备发射的无线电噪声测量方法

This standard specifies U.S. consensus standard methods, instrumentation, and facilities for measurement 9 of radio-frequency (RF) signals and noise emitted from electrical and electronic devices in the frequency 10 range 9 kHz to 40 GHz. It does not include generic nor product-specific emission limits. Where possible, the specifications herein are harmonized with other national and international standards used for similar purposes.