成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

厨房水槽检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 4214.16-2022家用和类似用途电器噪声测试方法 废弃食物处理器的特殊要求

增加:本文件适用于独立使用的家用和类似用途电动废弃食物处理器。该器具带有或不带有自动程序控制,采用冷水供应,永久连接到供水和排污系统,连接到厨房水槽排水管并置于厨房橱柜内。代替:GB/T 6881.2—2017、GB/T 6881.3—2002和GB/T 3767—2016可用于测试废弃食物处理器发射的噪声。代替:GB/T 3767—2016中所列方法适用于任意尺寸的声源。当使用GB/T 6881.2—2017和GB/T 6881.3—2002时,应注意包含被测废弃食物处理器橱柜的大尺寸满足GB/T 6881.2—2017和GB/T 6881.3—2002中1.3规定的要求。

SN/T 4847-2017卫生洁具耐急冷急热性试验方法

本标准规定了洗面器、洗涤槽、淋浴盆、浴缸等卫生洁具的耐急冷急热性试验方法。本标准适用于洗面器、洗涤槽、淋浴盆、浴缸等卫生洁具的耐急冷急热性的试验。

UL 150-2004天线旋转器

1.1 These requirements cover antenna rotators intended for household and commercial use on supplycircuits in accordance with the National Electrical Code, NFPA 70.1.2 An antenna rotator generally consists of:a) A mast-mounted (generally outdoors), motorized drive unit that rotates the antenna to thedesired receiving azimuth,b) An indoor-located (usually near television- or radio-receiving equipment) user-operatedcontrol unit that delivers operating power and direction signals to the drive unit, and,c) A length of multiple-conductor Class-2 circuit cable to electrically interconnect the drive unitand the control unit. Some antenna rotating units may control antenna elevation separately or in addition to azimuth. In some cases, the drive unit may be located indoors.1.3 The power used to drive the motor of an antenna rotator is derived from a circuit complying with Class 2 limitations in accordance with Article 725 of the National Electrical Code, ANSI/NFPA 70.1.4 These requirements do not cover systems that use a stationary antenna and change or rotate thereceiving pattern by electronic or switching means. Such systems are covered by the Standard forAudio-Video Products and Accessories, UL 1492.

UL 174-2004家用电蓄水热水器

The following changes in requirements are being proposed: 1. Revised Label Requirements for Household Storage Tank Water Heater when Connected to a Supplemental Heat Source.

UL 1863-2004通信电路附件

1.1 These requirements cover telecommunications-circuit accessories, such as jack and plug assemblies,quick-connect terminal assemblies, telephone wall plates, telephone extension cords, cross-connectterminal-block assemblies, maintenance terminal modules, terminal enclosures, cable-splice enclosures,network-interface devices, wire-guide assemblies, and connector boxes.1.2 These devices are intended to be used in telecommunications networks that have an operatingroot-mean-square (rms) voltage to ground less than 150 volts and installed or used in accordance withthe National Electrical Code, ANSI/NFPA 70.1.3 These requirements do not cover telephone equipment such as telephone answering devices,residential telephone instruments, telephone dialers, cordless phones, key systems, and private-branchexchange equipment that is covered by the Standard for Information Technology Equipment – Safety –Part I: General Requirements, UL 60950-1. Also, these requirements do not cover:a) Telephone protectors that are covered by the Standard for Protectors for Paired-ConductorCommunications Circuits, UL 497, andb) Secondary protectors that are covered by the Standard for Secondary Protectors forCommunications Circuits, UL 497A.1.3 revised May 14, 20041.4 These requirements do not cover receiver/transmitter-type devices. Equipment of this type is coveredby the Standard for Audio-Video Products and Accessories, UL 1492, or the Standard for Audio/Video andMusical Apparatus for Household, Commercial, and Similar General Use, UL 6500. These requirementsdo not cover cellular telephones or cellular devices. Equipment of this type is covered by UL 1492.1.4 revised May 14, 20041.5 These requirements may be used, directly or by reference, to investigate portions of other equipment,not classified as telecommunications-equipment accessories, that may be connected to atelecommunications network, insofar as they may be applicable to such equipment.1.6 These requirements do not cover wires and cables intended to be permanently installed in a buildingin accordance with Article 800 of the National Electrical Code, ANSI/NFPA 70.

EN 13310-2015厨房水槽.功能要求和测试方法

This European Standard specifies the functional requirements of and test methods for kitchen sinks for domestic purposes, which ensure that the product, when installed in accordance with the manufacturers' instructions, gives satisfactory performance. NOTE 1 For the purposes of this standard, the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings. This document does not specify aesthetic requirements and the overall dimensions of kitchen sinks. It does not apply to industrial kitchen sinks. NOTE 2 All drawings are examples only; other forms are permissible.

GSO EN 695-2011厨房水槽.连接尺寸

This European Standard specifies connecting dimensions for kitchen sinks used for domestic purposes, regardless of the material from which they are manufactured. NOTE 1 For the purposes of this standard the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings, except when special medical provisions are required. NOTE 2 The figures are given by way of example; other designs are possible. This European Standard does not apply to industrial kitchen sinks.

GSO EN 13310-2011厨房水槽.功能要求和试验方法

This European Standard specifies the functional requirements of and test methods for kitchen sinks for domestic purposes, which ensure that the product, when installed in accordance with the manufacturers’ instructions, gives satisfactory performance. NOTE 1 For the purposes of this standard the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings. This standard does not specify aesthetic requirements and the overall dimensions of kitchen sinks. It does not apply to industrial kitchen sinks. NOTE 2 All drawings are examples only; other forms are permissible.

NF D12-215-2018厨房水槽. 功能要求和试验方法

!La présente Norme européenne"détermine les !caractéristiques"fonctionnelles et les méthodes d'essai relatives aux éviers de cuisine à usage domestique qui garantissent que le produit, installé selon les instructions du fabricant, donne une performance satisfaisante.Pour les besoins de la présente norme, le terme " usages domestiques " s'applique à l'utilisation dans les hôtels, logements pour étudiants, hôpitaux et bâtiments similaires.Ce document ne détermine pas de !caractéristiques"en termes d'esthétique et de dimensions hors tout.!Il"ne s'applique pas aux éviers de cuisine à usage industriel.Tous les dessins ne sont donnés qu'à titre d'exemples ; d'autres formes sont admissibles.

NF D14-400-2008卫生设备.高填料含量的甲基丙烯酸分解物

La présente Norme européenne spécifie des méthodes d'essai permettant de mesurer les caractéristiques des dispersions méthacryliques et des appareils sanitaires produits à partir de ces dispersions par polymérisation.

TS EN 695-2007厨房水槽. 连接尺寸

This standard specifies the connecting dimensions for kitchen sinks for domestic purposes, regardless of the material used for their manufacture. This standard is applicable to kitchen sinks for use in residential (domestic) houses, guest houses and similar premises. This standard does not apply to industrial kitchen sinks.

上一篇压力冲洗装置检测 下一篇民用装饰镜检测

相关阅读

了解更多检测知识

醋酸纤维素检测

醋酸纤维素检测围绕结构鉴别、取代度测定、分子量分析、色谱纯度检测及理化性能测试展开。红外光谱法用于确认酯键结构与乙酰化程度,皂化回滴法测定取代度,凝胶渗透色谱法评价分子量分布,高效液相色谱与气相色谱质谱联用分析残留杂质,为原料验收与产品质量评价提供数据依据。

2026-10-27 | [其他]

重金属含量(以Pb计)检测

重金属含量(以Pb计)检测通过样品消解前处理,采用原子吸收光谱法、ICP-MS法或分光光度法定量测定铅含量。本文系统介绍检测原理、前处理要点、各方法适用差异、灵敏度与回收率等指标要求,以及限量判定标准与应用场景,供生产企业与送检方参考。

2026-10-27 | [其他]

热转印膜检测

热转印膜检测涵盖外观规格、色牢度、附着力、耐磨耐候、拉伸强度与厚度等项目。检测流程标准状态调节、规范裁样与转印制片,采用摩擦色牢度仪、划格法、磨耗试验机、氙灯老化、万能材料试验机及测厚仪等手段,依据相关方法标准测定,据实判定各项性能是否符合要求。

2026-10-27 | [其他]

合成辣椒素检测

合成辣椒素检测以食品、调味料及喷雾类产品中人工合成辣椒碱类物质为对象,常规采用HPLC法完成含量测定,辅以GC-MS法进行定性确证。样品经提取净化后进入色谱分析,方法性能以检出限、线性范围与回收率评价,检测结果可用于非法添加筛查与产品合规判定。

2026-10-27 | [其他]

拖拉机前驱动桥检测

拖拉机前驱动桥检测覆盖桥壳几何精度与刚度、焊缝无损检测、齿轮精度与接触斑点、半轴扭转强度、密封性及台架传动效率与疲劳寿命等项目,采用三坐标测量、磁粉与超声波探伤、光谱分析及台架试验等技术手段,适用于新品定型、出厂检验、供应商验收与失效分析等场景。

2026-10-27 | [其他]

电缆桥架检测

电缆桥架检测覆盖钢制、铝合金、玻璃钢等材质的托盘、梯架及支吊架,主要项目几何尺寸测量、安全工作载荷试验、挠度与残余变形测定、镀层厚度与附着力检验及盐雾腐蚀试验等。本文按送样要求、检测方法、性能指标、判定标准与应用场景逐步说明,帮助读者掌握桥架检测的完整流程与要点。

2026-10-27 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通