燃气装置用手动燃气阀检测

燃气装置用手动燃气阀检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 14536.19-2017家用和类似用途电自动控制器 电动燃气阀的特殊要求，包括机械要求

本部分适用于家用和类似用途设备中的或随这些设备一起使用的电动燃气阀，这些设备使用电与气态燃料，如打算用于气体燃烧设备的人工煤气、天然气和液化石油气的组合使用。本部分也适用于使用NTC和PTC热敏电阻器的电动燃气阀，对它们的附加要求包含在附录J中。本部分适用于电动燃气阀固有的安全性，适用于与设备安全有关的操作值、操作时间和操作程序，以及适用于在家用或类似设备内、设备中或随设备一起使用的电动燃气装置的试验。同时，也可扩展用于没有专用标准，工业用途的产品，如用于中央供暖、空调、工艺加热等。本部分也适用于在GB 4706.1范围内的器具使用的控制器。本部分不适用于专门用于工业用途的电动燃气阀。对于非一般家用的但仍可能用于公共场所的，如给商店、轻工业工厂和农场中的非人士使用的设备，其电动燃气阀也包括在本部分范围内。本部分定义了很多作为“在考虑中”的机械性能。在使用本部分时应确定这些要求，直到这些机械要求被合并到本部分中。符合本部分的电动燃气阀仍需对阀的机械性能进行进一步试验。本部分适用于那些在电气上和/或机械上与电动燃气阀组合在一起的人工控制器。本部分不适用于标称连接尺寸超过DN150的电动燃气阀。本部分适用于大工作压力高达400 kPa(4 bar)的电动燃气阀。在下文中，术语“阀”指电动燃气阀(包括原动机构和阀体)。

GB 50028-2006城镇燃气设计规范

本规范适用于向城市、乡镇或居民点供给居民生活、商业、工业企业生产、采暖通风和空调等各类用户作燃料用的新建、扩建或改建的城镇燃气工程设计。 注:1 本规范不使用于城镇燃气门站以前的怅距离输气管道工程。 2 本规范不适用于工业企业自建供生产工艺用且燃气质量不符合本规范质量要求的燃气工程设计，但自建供生产工艺用且燃气质量符合本规范要求的燃气工程设计，可按本规范执行。工业企业内部自供燃气给居民使用时，供居民使用的燃气质量和工程设计应按本规范执行。 3 本规范不适用于海洋和内河轮船、铁路车辆、汽车等运输工具上的燃气装置设计。

CJ/T 180-2014建筑用手动燃气阀门

本标准规定了建筑用手动燃气阀门(以下简称阀门)的分类及型号,材料、结构和连接尺寸,要求,试验方法,检验规则,标志、包装、运输和贮存。本标准适用于公称压力不大于1.6 MPa、公称尺寸不大于100 mm、工作温度不超出-20 ℃~60 ℃且其下限不低于燃气露点温度,安装在建筑物内外的非直埋燃气装置与设施上的手动燃气球阀和底部密封的旋塞阀。本标准所指燃气为符合GB/T 13611规定的燃气。

CJJ 94-2009城镇燃气室内工程施工与质量验收规范

为统一城镇燃气室内工程的施工与质量验收，保证城镇燃气室内工程的施工质量，确保安全供气，制定本规范。本规范适用于供气压小于或等于0.8MPa（表压）的新建、扩建和改建的城镇居民住宅、商业用户、燃气锅炉房（不含锅炉本体）、实验室、工业企业（不含用气设备）等用户室内燃气管道和用气设备安装的施工与质量验收。

JC/T 2352-2016建筑陶瓷企业安全生产规范

本标准规定了建筑陶瓷企业安全生产的机构和人员、安全基础管理、设备安全、作业安全、承包商和主要供应商的安全管理以及事故预防和处理。本标准适用于建筑陶瓷生产企业。

JC/T 2354-2016卫生陶瓷企业安全生产规范

本标准规定了卫生陶瓷企业(下称企业)安全生产的机构和人员、安全基础管理、设备安全、作业安全、承包商和主要供应商的安全管理以及事故预防和处理。本标准适用于制造加工卫生陶瓷的生产企业。

UL 1776-2002高压清洗机

These requirements cover inverters ,converters ,charge controllers ,and output controllers intended for use in stand-alone(not grid connected) or utility-interactive (grid-connected) power systems .Utility-interactive inverters and converters are intended to be installed in parallel with an electric supply system or an electric utility to supply common loads.

DIN EN 303-7-2007加热锅炉.第7部分:用标称热输出功率小于1000 kW的强排风燃炉装备的燃气中央加热锅炉

This European Standard specifies the requirements and test methods for the contruction,the safety and the rational energy usage for gas-fired standard and low temperature central heating boilers equipped with a forced draught burner.These boilers comprise a boiler body and a forced draught gas burner brought together at the producer's assembly facility,the whole being disigned and marketed as a complete boiler.This standard does not apply to the case of the assembly of a boiler body and a forced draught gas burner designed and marketed separately.In this case,EN 303-3 applies.This European Standard applies to type B boilers with a nominal heat output not exceeding 100 kw with a water temperature at normal operation not exceeding 105°C and with a maximum water-side operating pressure not exceeding 8 bar.This European Standard does not contain all the necessary requirements for:- condensing boilers and combination boilers;- boilers intended to be installed in the open;- boilers permanently fitted with more than one flue outlet;- boilers intended to be connected to a common flue having mechanical extraction;- boilers equipped with several combustion chambers.This European Standard does not apply to living-space dedicated boilers(see 3.6).This European Standard only covers type testing.

DIN EN 13278-2014前开式独置燃气加热器.德文版本EN 13278-2013

This European Standard specifies the requirements and test methods for the construction, safety, marking and rational use of energy of open fronted gas-fired independent space heaters with and without a fan to assist with the transportation of flue gases. Although the fan may be mounted outdoors, this standard only covers appliances where the body of the appliance is indoors. This standard applies to types B11AS, B11BS, B14AS, and B14BS open fronted gas-fired independent space heating appliances that incorporate an atmospheric burner, that are connected directly to an open flue or to a device to evacuate the products of combustion (open-flued appliances), that have a nominal heat input not exceeding 20 kW (based on the net calorific value) and that are delivered with the gas-carrying components, burner (s), combustion chamber and heat exchanger fully assembled.

BS 5546-2010额定输入不超过70kW的家用燃气供热水装置的安装和维修规范

This British Standard specifies requirements for the selection,installation, inspection, commissioning and maintenance of gas‑firedwater-heating appliances, which have a rated heat input notexceeding 70 kW, based on net calorific value.It applies to water-heating appliances utilizing 1st, 2nd or 3rd familygases designed to operate in the condensing or non‑condensingmode for the supply of hot water for domestic purposes in domesticdwellings or domestic dwellings in commercial premises.This standard does not apply to:a) water-heating appliances with a rated input of over 70 kW;b) hot water supply systems in multiple dwellings supplied from acentral source.It does not cover the detailed design and installation of the whole hotwater distribution system, which was specified in BS 5449.This standard applies to water-heating appliances which carry aCE mark and also to previously used water-heating appliances whichdo not carry the CE mark (see 5.3.1).

ANSI Z21.5.1-2006燃气衣物干燥器、卷I、 1型干衣机(与CSA 7.1b相同)

Details test and examination criteria for Type 1 clothes dryers for use with natural, manufactured or mixed gases, liquefied petroleum gases or LP gas-air mixtures.

ANSI Z21.18-2007燃气器具压力调节器(与CSA 6.3相同)

Details test and examination criteria for gas appliance pressure regulators for use with natural, manufactured and mixed gases, liquefied petroleum gases and LP gas-air mixtures. Such devices, either individual or in combination wit other controls, are i