通用与包装用低密度聚乙烯薄膜检测
GB/T 4456-2008包装用聚乙烯吹塑薄膜
本标准规定了包装用聚乙烯吹塑薄膜（以下简称薄膜）的产品分类、要求、试验方法、检验规则以及标志、包装、运输、贮存。本标准适用于低密度聚乙烯（PE-LD）、线形低密度聚乙烯（PE-LLD）、高密度聚乙烯（PE-HD）等树脂共混为主要原料，用吹塑法生产的直接包装用的复合膜基材用薄膜。
GB/T 4588.3-2002印制板的设计和使用
本标准涉及印制板的设计和使用，而与制造方法无关。本标准就印制板的设计和使用对印制板设计者和使用者提出建议。
GB 50212-2014建筑防腐蚀工程施工规范
本规范适用于新建、改建、扩建的建筑物和构筑物防腐蚀工程的施工。
HG/T 20663-1999化工粉体产品计量、包装及码垛系统设计规定
1.0.1为了统一化工粉粒产品计量、包装及码垛系统工程设计的原则和标准，更好地贯彻执行的技术经济政策和技术标准，进一步提高设计水平和设计质量，加快设计进度，特制定本规定。 1.0.2本规定适用于大、中型化工企业的新建或扩建工程的袋装化工粉粒产品计量、包装及码垛系统的设计。小型化工企业及其它行业建设工程的袋装粉粒产品计量、包装及码垛系统设计也可参照使用。 1.0.3化工粉粒产品计量、包装及码垛系统的设计应结合工程实际，吸取国内外先进技术经验，采用成熟的新工艺、新设备，遵守劳动安全卫生和环境保护的有关规定，力求做到技术先进、布置合理、运行可靠、操作安全、维护方便、经济实用。 1.0.4化工粉粒产品计量、包装及码垛系统的设计应根据全厂生产规模的远景规划，全面规划、分期建设，留有扩建余地。若通过技术经济比较确认分期建设不合理时，亦可一次建成。在扩建设计时，应结合原有生产系统的实际情况，充分发挥原有设施的能力。 1.0.5化工粉粒产品计量、包装及码垛系统设计，除应符合本规定外，尚应符合现行的有关标准的规定。
HB 5205-1982铝塑布复合薄膜
本标准适用于以工业铝箔和纺织材料为基材，经挤塑热复合低密度聚乙烯制成的铝塑布复合薄膜，该材料可供精密机械、仪器、仪表等产品及零部件长期贮存时防潮包装之用。
HB 7685-2001飞机燃油系统污染控制要求
本标准规定了飞机燃油系统及其附件的油液固体颗粒污染度、游离水含量的验收、控制水平，并相应规定了飞机燃油系统在设计、制造、安装、试验、使用和维护等方面的污染控制设计、工艺和一般技术要求。 本标准适用于飞机燃油系统及其附件的设计、制造、安装、试验、使用和维护的污染控制。
SH/T 1780-2015异戊二烯橡胶(IR)
本标准规定了异戊二烯橡胶（简称“异戊橡胶”）的产品分类、技术要求、试验方法、检验规则及包装、标志、贮存、运输。本标准适用于在稀土催化体系下经溶液聚合制得的异戊橡胶。
JB/T 5421-2013塑料薄膜回收挤出造粒机组
本标准规定了塑料薄膜回收挤出造粒机组的规格系列、型号、组成、基本参数、要求、试验及检测方法、检验规则、标志、包装、运输和贮存。本标准适用于塑料薄膜回收的异径单螺杆塑料薄膜回收挤出造粒机组(以下简称机组),不适用于双阶单螺杆挤出造粒机组及其他用途塑料挤出机。
JB/T 10437-2004电线电缆用可交联聚乙烯绝缘料
本标准规定了35kV及以下交联聚乙烯绝缘电线电缆用可交联聚乙烯绝缘料的技术要求、试验方法、检验规则、包装、标志、运输和贮存。 本标准适用于以低密度聚乙烯为基料、掺有交联剂等助剂经塑化造粒制成的过氧化物交联聚乙烯、硅烷交联聚乙烯和辐照交联聚乙烯的绝缘材料。其适用范围为： (1～35)kV过地氧化物交联聚乙烯绝缘料； (1～35)kV硅烷交联聚乙烯绝缘料； (1～10)kV辐照交联聚乙烯绝缘料。
ASTM D4635-1995通用和包装用低密度聚乙烯薄膜标准规范
1.1 This specification covers unpigmented, unsupported, low-density polyethylene films (hereafter referred to as film or films) from Class I polyethylenes per Specification D4976. Note 1-The density of a film will not necessarily be equal to the density of a molded plaque from the same resin. Note 2-Blends of ethylene/vinylacetate (EVA) with low-density polyethylene may have densities up to 0.929 g/cm. 1.2 This specification is applicable to homopolymer polyethylene, but is not restricted to it. It is applicable to films made from copolymer, and also applicable to films made from blends of homopolymers and copolymers, including ethylene/vinylacetate copolymers. 1.3 The thickness of the films covered by this specification is 100 181m or less (0.004 in. or less), inclusive. The maximum width of the sheet or layflat is 3.00 m (120 in.). 1.4 This specification does not cover oriented heat-shrinkable films. 1.5 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all of the requirements of this specification are met and as long as any specific requirements as governed by the producer and end user are also met. (See Note 3.) Note 3-Guide D5033 describes terminology and definitions related to recycled plastics. 1.6 This specification defines the levels of the various physical properties from which specifications for specific films may be described. The levels of physical properties required by a film for a given application are selected from Section 6. However, Sections 2 - 5 relating to tolerances shall apply without change to all film falling within the scope indicated by the title and 1.1 - 1.4. 1.7 This specification covers dimensional tolerances, classifications, intrinsic quality requirements, and test methods. The dimensional tolerances include thickness, width, and length or yield. Classification defines types, classes, surfaces, and finishes. The intrinsic quality requirements include density, workmanship, tensile strength, heat sealability, and odor, as well as the classification properties for impact strength, coefficient of friction, optical properties, and surface treatment. A sampling method is included. 1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.9 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 4-There is no similar or equialent ISO specification.
ASTM D4635-2001通用和包装用低密度聚乙烯薄膜标准规范
1.1 This specification covers unpigmented, unsupported, low-density polyethylene films (hereafter referred to as film or films) from Class I polyethylenes per Specification D4976. Note 1-The density of a film will not necessarily be equal to the density of a molded plaque from the same resin. Note 2-Blends of ethylene/vinylacetate (EVA) with low-density polyethylene may have densities up to 0.929 g/cm. 1.2 This specification is applicable to homopolymer polyethylene, but is not restricted to it. It is applicable to films made from copolymer, and also applicable to films made from blends of homopolymers and copolymers, including ethylene/vinylacetate copolymers. 1.3 The thickness of the films covered by this specification is 100 181m or less (0.004 in. or less), inclusive. The maximum width of the sheet or layflat is 3.00 m (120 in.). 1.4 This specification does not cover oriented heat-shrinkable films. 1.5 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all of the requirements of this specification are met and as long as any specific requirements as governed by the producer and end user are also met. (See Note 3.) Note 3-Guide D5033 describes terminology and definitions related to recycled plastics. 1.6 This specification defines the levels of the various physical properties from which specifications for specific films may be described. The levels of physical properties required by a film for a given application are selected from Section 6. However, Sections 2 - 5 relating to tolerances shall apply without change to all film falling within the scope indicated by the title and 1.1 - 1.4. 1.7 This specification covers dimensional tolerances, classifications, intrinsic quality requirements, and test methods. The dimensional tolerances include thickness, width, and length or yield. Classification defines types, classes, surfaces, and finishes. The intrinsic quality requirements include density, workmanship, tensile strength, heat sealability, and odor, as well as the classification properties for impact strength, coefficient of friction, optical properties, and surface treatment. A sampling method is included. 1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.9 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 4-There is no similar or equialent ISO specification.
ASTM D4635-2008通用和包装用低密度聚乙烯制聚乙烯薄膜的标准规范
1.1 This specification covers unpigmented, unsupported, low-density polyethylene films (hereafter referred to as film or films) from Class 1 polyethylenes per Specification D 4976. Note 18212;The density of a film will not necessarily be equal to the density of a molded plaque from the same resin. Note 28212;Blends of ethylene/vinylacetate (EVA) with low-density polyethylene may have densities up to 0.929 g/cm3. 1.2 This specification is applicable to homopolymer polyethylene, but is not restricted to it. It is applicable to films made from polyethylene copolymers, and also applicable to films made from blends of homopolymers and copolymers, including ethylene/vinylacetate copolymers. 1.3 The thickness of the films covered by this specification is 100 x03BC;m or less (0.004 in. or less), inclusive. The maximum width of the sheet or layflat is 3.00 m (120 in.). 1.4 This specification does not cover oriented heat-shrinkable films. 1.5 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all of the requirements of this specification are met and as long as any specific requirements as governed by the producer and end user are also met. (See Note 3.) Note 38212;Guide D 7209 describes terminology and definitions related to recycled plastics. 1.6 This specification defines the levels of the various physical properties from which specifications for specific films may be described. The levels of physical properties required by a film for a given application are selected from Section 6. However, Sections 2-5 relating to tolerances shall apply without change to all film falling within the scope indicated by the title and 1.1-1.4. 1.7 This specification covers dimensional tolerances, classifications, intrinsic quality requirements, and test methods. The dimensional tolerances include thickness, width, and length or yield. Classification defines types, classes, surfaces, and finishes. The intrinsic quality requirements include density, workmanship, tensile strength, heat sealability, and odor, as well as the classification properties for impact strength, coefficient of friction, optical properties, and surface treatment. A sampling method is included. 1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.9 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 48212;There is no similar or equivalent ISO specification.
ASTM D4635-2008a通用和包装用低密度聚乙烯薄膜标准规范
1.1 This specification covers unpigmented, unsupported, low-density polyethylene films (hereafter referred to as film or films) from Class 1 polyethylenes per Specification D 4976. Note 18212;The density of a film will not necessarily be equal to the density of a molded plaque from the same resin. Note 28212;Blends of ethylene/vinylacetate (EVA) with low-density polyethylene may have densities up to 0.929 g/cm3. 1.2 This specification is applicable to homopolymer polyethylene, but is not restricted to it. It is applicable to films made from polyethylene copolymers, and also applicable to films made from blends of homopolymers and copolymers, including ethylene/vinylacetate copolymers. 1.3 The thickness of the films covered by this specification is 100 x03BC;m or less (0.004 in. or less), inclusive. The maximum width of the sheet or layflat is 3.00 m (120 in.). 1.4 This specification does not cover oriented heat-shrinkable films. 1.5 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all of the requirements of this specification are met and as long as any specific requirements as governed by the producer and end user are also met. (See Note 3.) Note 38212;Guide D 7209 describes terminology and definitions related to recycled plastics. 1.6 This specification defines the levels of the various physical properties from which specifications for specific films may be described. The levels of physical properties required by a film for a given application are selected from Section 6. However, Sections 2-5 relating to tolerances shall apply without change to all film falling within the scope indicated by the title and 1.1-1.4. 1.7 This specification covers dimensional tolerances, classifications, intrinsic quality requirements, and test methods. The dimensional tolerances include thickness, width, and length or yield. Classification defines types, classes, surfaces, and finishes. The intrinsic quality requirements include density, workmanship, tensile strength, heat sealability, and odor, as well as the classification properties for impact strength, coefficient of friction, optical properties, and surface treatment. A sampling method is included. 1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.9 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 48212;There is no similar or equivalent ISO specification.
DIN-Fachbericht CEN/TR 15356-1-2006与食品接触的材料和人造材料的迁移试验和分析数据的验证和释义
This Technical Report gives guidance in support of Directives adopted by the European Union in the Food Contact Materials Sector and is intended to aid Food Control Authorities and industry enforce and comply with those Directives.
