涂层玻璃检测
GB/T 7113.2-2014绝缘软管 第2部分:试验方法
GB/T 7113的本部分规定了包括热收缩管在内的绝缘软管的试验方法。这类软管主要被用于电气设备的导体部分和接头处的绝缘。本部分适用于绝缘软管。
GB/T 17495-2009港口门座起重机
本标准规定了港口门座起重机(以下简称起重机)的技术要求、试验方法、检验规则、标志和运输。本标准适用于港口件杂货、散货、集装箱、成套设备等装卸作业用的起重机。船厂、电站用的同类起重机亦可参照使用。
GB/T 18144-2008玻璃应力测试方法
本标准规定了玻璃表面应力、玻璃边缘应力测试的有关定义和测试方法。本标准中表面应力测试方法适用于浮法玻璃制造的钢化玻璃、半钢化玻璃；边缘应力测试方法适用于钢化玻璃、半钢化玻璃、汽车前风窗用夹层玻璃、热弯玻璃。化学钢化玻璃可参照使用本标准中表面应力测试方法。本测试方法为无损测量的测试方法。
GB/T 36400-2018建筑用装饰玻璃术语
本标准界定了建筑用装饰玻璃的通用术语、产品种类及与生产工艺相关术语及定义。本标准适用于建筑用装饰玻璃的设计、生产与应用领域。
GB/T 37594-2019钢质管道抗紫外线三层熔结粉末防腐外涂层技术规范
本标准规定了钢质管道抗紫外线三层熔结粉末防腐外涂层的结构、等级、要求、检验与规则、涂层的修补和重涂、产品标识、贮存和运输、现场补口、安全、卫生和环境保护、文件管理要求。本标准适用于公称直径≥15 mm，工作温度为-30 ℃~100 ℃的架空环境的钢质管道抗紫外线三层熔结粉末防腐外涂层的设计、施工及检验。其他工况可参照执行。
GB 50256-2014电气装置安装工程 起重机电气装置施工及验收规范
本规范适用于建设工程中额定电压10kV及以下的各式起重机、电动葫芦的电气装置和滑触线安装工程的施工及验收。
HB 7041-1994航空行业非金属材料代码
本标准规定了航空行业常用非金属材料的分类原则、编码方法和具体的分类与代码表。 本标准适用于航空行业各企事业单位。
JGJ 66-2015博物馆建筑设计规范
本规范适用于新建、扩建和改建的博物馆建筑设计。
ISO 11479-1-2011建筑玻璃.镀膜玻璃.第1部分:物理缺陷
This part of ISO 11479 specifies optical quality requirementsnfor coatings applied to glass using either pyrolytic, sol-gel ornvacuum (sputtering) deposition methods for use in building glazing.nMore specifically, this part of ISO 11479 relates to low-e andnsolar-control coated glass. This part of ISO 11479 is notnapplicable to patterned or other optically distorting glass.
ISO 11479-2-2011建筑玻璃.镀膜玻璃.第2部分:正面颜色
This part of ISO 11479 specifies a method for objectivenevaluation of the colour of coated glass when used in façades andnviewed from the outside, as well as for measuring colourndifferences within the same glass pane and between two adjacentnpanes in the same façade. This part of ISO 11479 does not specifynrequirements for determining colour differences of transmittedncolour as viewed from the inside or outside of a façade, nor forninternal reflected colour. The comparison should only be undertakennfor panes of the same glass type, composition and interiornconditions and situated in the same plane of a façade.nSpecific requirements are given for coated glass, dependent uponnits light transmittance and reflectance.nThis part of ISO 11479 is not applicable to curved or bentnglass, which is specifically excluded for technical reasons.nNOTE Information on the perception, quantification andnmeasurement of colour is given in Annex A.
ISO 14382-2012工作场所空气.使用1-(2-吡啶基)哌嗪涂层玻璃纤维过滤器测定及通过带有紫外和荧光检测器的液相色谱分析甲苯二异氰酸酯蒸气
This International Standard gives general guidance for thensampling and analysis of airborne toluene diisocyanate (TDI) innworkplace atmospheres. The procedure specified in thisnInternational Standard is especially suitable for short (15min)andnlong-term (4 h) sampling and analysis of 2,4- and 2,6-TDInvapours.nThe upper limit for this method is approximately 85 μg of TDInper sample. This is a conservative upper limit based on thenrequirements of maintaining a sufficient amount of reagent on thencoated glass fibre filter while permitting a 4 h sample to bencollected at 1 l/min from an atmosphere containing 50 nl/l ofnTDI.nThe quantitation limits for this method are 0,039 μg for 2,4-TDInand 0,034 μg for 2,6-TDI using a fluorescence detector. Thesenlimits, for a 15-min sample collected at 1 l/min, are equivalent ton0,036 nl/l for 2,4-TDI, and 0,32 nl/l for 2,6-TDI. For a 4 h samplencollected at 1 l/min, the limits are equivalent to 0,022 nl/l forn2,4-TDI and 0,020 nl/l for 2,6-TDI.nThe co
UL 55A-2004组合式屋面覆盖材料
1.1 These requirements cover the following materials for use in the construction of built-up roof coverings: a) Hot-Mopping Asphalt - For use in the construction of coverings having either no surfacing or utilizing surfacings of cold-application roof coating on inclines not exceeding 12 inches (305 mm) to the horizontal foot, and for use in the construction of coverings surfaced with gravel, crushed stone, or crushed slag, on inclines not exceeding 3 inches (76 mm) to the horizontal foot. b) Asphalt-Saturated Organic Felt - Type 15 (plain or perforated) and Types 20 and 30 (plain), including cap and base sheets. c) Coal-Tar Pitch - For use in the construction of coverings surfaced with gravel, crushed stone, or crushed slag, on inclines not exceeding 3 inches (76 mm) to the horizontal foot. d) Coal-Tar Saturated Organic Felt - Type 15. e) Asphalt-Coated Glass-Fiber Mat (Felt) - Type G1 (ply sheets), Type G2 (cap and base sheets), and Type G3 (granular-surfaced cap sheets).
