电子和通信设备用变压器和电感器检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 8554-1998电子和通信设备用变压器和电感器测量方法及试验程序

本标准规定了电子和通信设备用变压器和电感器的测量方法和试验程序，这些测量方法和试验程序可包含在这类元件的任何规范中，特别是构成IEC电子元器件质量评定体系（IECQ体系）的那部分规范之中。

GB/T 11441.1-2012通信和电子设备用变压器和电感器铁心片第1部分：机械和电性能

GB/T 11441的本部分规定了铁心片的特性、本部分适用于铁心片主要用于变压器和电感器、这些铁心片是用IEC 60404-8-4:1998和IEC 60404-8-7:1998规定的磁性电工钢片(带)制成的、

GB/T 12668.3-2012调速电气传动系统.第3部分 :电磁兼容性要求及其特定的试验方法

GB 12668 的本部分规定了电气传动系统(PDS)的电磁兼容性(EMC)要求。PDS的定义如3.1中所述。这里的电气传动系统包括调速的交流电动机传动和直流电动机传动。这些EMC要求是针对变流器输入和/或输出电压(线电压)有效值在交流35 kV以下的PDS而规定的。本部分适用于对PDS的评价。同时也可用于对单独销售的CDM或 BDM(见3.1)的评价。本部分包含:对于要投放市场的产品的符合性评价要求;对于在设备投放市场之前不能测量出高频发射的场合(这类PDS在3.2.6中被定义为C4类)推荐的工程设计实践。

GB/T 14860.1-2012电子和通信设备用变压器和电感器第1部分：通用规范

GB/T 14860的本部分为通用规范,它规定了变压器和电感器制造厂为获得依据IECQ QC 001002:1986中11.7规定的能力批准必须遵循的要求和用以评定能力的元件试验程序、本部分适用于通信和电子设备的变压器和电感器,其中包括多相变压器、本部分还规定了标识、延期交货和订货要求,并给出了标准额定值和特性、此外,还规定了定购的元件质量一致性检验方法、

GB/T 14860.3-2012电子和通信设备用变压器和电感器第3部分：按能力批准程序评定质量的电源变压器分规范

GB/T 14860的本部分规定了按GB/T 14860.1-2012规定的能力批准程序放行的电源变压器详细规范编制方法。本部分包括空白详细规范(BDS)。空白详细规范规定了格式并指出了适合于这类元件的试验；而终选择列入检查一览表的试验是由该规范的编写者决定的。此规范还规定了相应的额定值和特性。本部分规定的元器件与基频基本对称波形下的大传输功率有关。

GB/T 14860.4-2012电子和通信设备用变压器和电感器.第4部分：按能力批准程序评定质量的开关电源变压器分规范

GB/T 14860的本部分规定了按GB/T 14860.1—2012规定的能力批准程序放行的开关电源变压器详细规范编制方法。本部分包括空白详细规范(BDS),空白详细规范规定了格式并指出了适合于这类元件的试验;而终选择列入检查一览表的试验是由该规范的编写者决定。此规范还规定了相应的额定值和特性。本部分规定的元件与工作在开关状态的半导体器件连在一起用以传输功率,其输入波形为正弦或非正弦、对称或非对称的波形。

GB/T 15290-2012电子设备用电源变压器和滤波扼流圈总技术条件

本标准规定了电子设备用电源变压器、滤波扼流圈（以下统称“元件”）的技术要求、试验方法、检验规则及标志、包装、运输、贮存。本标准适用于工作电压不高于5000V、电源频率不高于1050Hz、重量不大于70kg的电子设备用干式电源变压器、滤波扼流圈。

SJ/T 10614-1995按能力批准程序评定质量的电子设备用电感器分规范

本规范规定了按GB/T 14860《电子和通信设备用变压器和电感器总规范》规定的能力批准程序放行的电感器详细规范制定方法。本规范包括空白详细规范(BDS)，空白详细规范规定了格式并规定了适合于这种类型元件的试验；而终选入检验一览表的试验项目是由该规范的制定者决定的。本规范还规定了相应的额定值和特性。

SJ/T 10615-1995按能力批准程序评定质量的电子设备用信号变压器分规范

本规范规定了按GB/T14860《电子和通信设备用变压器和电感器总规范》规定的能力批准程序放行的信号变压器详细规范制定方法。本规范包括空白详细规范(BDS)，空白详细规范规定了格式并规定了适合于这种类型元件的试验；而终选入检验一览表的试验项目是由该规范的制定者决定的。本规范还规定了相应的额定值和特性。本规范规定的元件主要涉及列单向和双向信号(信息)从电路的一部分向另一部分的传输。这些信号可具有一定的功率并覆盖某一频带。

SJ/T 10616-1995按能力批准程序评定质量的电子设备用脉冲变压器分规范

本规范规定了按GB/T 14860《通信和电子设备用变压器和电感器总规范》规定的能力批准程序放行的脉冲变压器详细规范制定方法。本规范包括空白详细规范(BDS)，空白详细规范规定了格式并规定了适合于这种类型元件的试验；而终选入检验一览表的试验项目是由该规范的制定者决定的。本规范还规定了相应的额定值和特性。本规范规定的元件主要涉及到单向脉冲，同时还涉及到这些脉冲的能量和信号从电路的一部分向另一部分的传输。小功率脉冲变压器用以传输信号，大功率脉冲变压器用以传输功率，但两者之间可不规定界限。

SL 73.5-2013水利水电工程制图标准电气图

本标准适用于水利水电工程电气制图。

JJG 726-2017标准电感器

本规程适用于电感范围1 μH~10 000 H、频率范围20 Hz~100 kHz的标准电感器的首次检定、后续检定和使用中检查。

IEC 61007-2020电子和通信设备用变压器和电感器. 测量方法和试验程序

This document describes a number of tests for use in determining the significant parameters and performance characteristics of transformers and inductors for use in electronics and telecommunication equipment. These test methods are designed primarily for transformers and inductors used in all types of electronics applications that can be involved in any specification for such components. Even though these tests can be useful to the other types of transformers used in power distribution applications in utilities, industry, and others, the tests discussed in this document can supplement or complement the tests but are not intended to replace the tests in standards for transformers. Some of the tests described are intended for qualifying a product for a specific application, while others are test practices used for manufacturing and customer acceptance testing. The test methods described here include those parameters most commonly used in the electronics transformer and inductor industry: electric strength, resistance, power loss, inductance, impedance, balance, transformation ratio and many others used less frequently.

IEC 61248-1-1996电子和通信设备用变压器和电感器第1部分:总规范

Generic specification which prescribes the compliance requirements for manufacturers of transformers and inductors for use in electronic equipment in order to obtain capability approval in accordance with 11.7 of QC 001002, and the component test schedules to be used for the assessment of that capability. It applies to components, including polyphase types, that are primarily intended for use in electronic and telecommunication equipment.

IEC 61248-2-1996电子和通信设备用变压器和电感器第2部分:采用能力批准程序的信号变压器分规范

Specifies how to prepare detail specifications for signal transformers to be released under the terms of IEC 1248-1 (QC 260000) capability approval. Includes a blank detail specification (BDS), which shows the format, and indicates which tests are considered to be appropriate to this type of component, although the final selection of tests to be included in the inspection schedule is at the discretion of the specification writer. It also lists appropriate ratings and characteristics.

IEC 61248-3-1996电子和通信设备用变压器和电感器第3部分:采用能力批准程序的电源变压器分规范

Specifies how to prepare detail specifications for power transformers to be released under the terms of IEC 1248-1 (QC 260000) capability approval. Includes a blank detail specification (BDS), which shows the format, and indicates which tests are considered to be appropriate to this type of component, although the final selection of tests to be included in the inspection schedule is at the discretion of the specification writer. It also lists appropriate ratings and characteristics.

IEC 61248-4-1996电子和通信设备用变压器和电感器第4部分:采用能力批准程序的开关电源变压器分规范

Specifies how to prepare detail specifications for power transformers for switched mode power supplies (SMPS) to be released under the terms of IEC 1248-1 (QC 260000) capability approval. Includes a blank detail specification (BDS), which shows the format, and indicates which tests are considered to be appropriate to this type of component, although the final selection of tests to be included in the inspection schedule is at the discretion of the specification writer. It also lists appropriate ratings and characteristics.

IEC 61248-5-1996电子和通信设备用变压器和电感器第5部分:采用能力批准程序的脉冲变压器分规范

Specifies how to prepare detail specifications for pulse transformers to be released under the terms of IEC 1248-1 (QC 260000) capability approval. Includes a blank detail specification (BDS), which shows the format, and indicates which tests are considered to be appropriate to this type of component, although the final selection of tests to be included in the inspection schedule is at the discretion of the specification writer. It also lists appropriate ratings and characteristics.

IEC 61248-6-1996电子和通信设备用变压器和电感器第6部分:采用能力批准程序的电感器分规范

Specifies how to prepare detail specifications for inductors to be released under the terms of IEC 1248-1 (QC 260000) capability approval. Includes a blank detail specification (BDS), which shows the format, and indicates which tests are considered to be appropriate to this type of component, although the final selection of tests to be included in the inspection schedule is at the discretion of the specification writer. It also lists appropriate ratings and characteristics.