海缆铠装用镀锌或锌合金钢丝检测

海缆铠装用镀锌或锌合金钢丝检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 32795-2016海缆铠装用镀锌或锌合金钢丝

本标准规定了海缆铠装用镀锌或锌合金钢丝的术语和定义、分类和标记、订货内容、尺寸、外形、重量及允许偏差、技术要求、检验方法、检验规则和包装、标志及质量证明书。本标准适用于海洋工程用光缆、电缆、光电复合缆、脐带缆铠装等类似用途的镀锌或锌合金圆形碳素钢丝(以下简称钢丝)。

EN ISO 13628-5-2009石油和天然气工业.水下采油系统的设计和操作.第5部分:海底缆线

This International Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes.

DIN EN 10257-2-2012电力电缆或通信电缆铠装用镀锌或锌合金非合金钢丝.第2部分:海底电缆.德文版本EN 10257-2-2011

This European Standard specifies requirements for the properties of non-alloy zinc or zinc alloy coated steel wires used for the armouring of either submarine power or telecommunication cables.

DIN EN ISO 13628-5-2010石油和天然气工业.水下采油系统的设计和操作.第5部分:海底缆线

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.

BS EN ISO 13628-5-2009石油和天然气工业.水下采油系统设计和操作.水下脐带管

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surfacesubsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.This part of ISO 13628 does not apply to a tube or hose rated lower than 7 MPa (1 015 psi).This part of ISO 13628 does not apply to electric cable voltage ratings above standard rated voltagesU0/U(Um) = 3,6/6(7,2) kV rms, where U0, U and Um are as defined in IEC 60502-1 and IEC 60502-2.