眼科光学镜片检测

眼科光学镜片检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

DIN EN 16128-2016眼科光学.镜框和镜片部分释放的镍含量测试的参考方法;德文版本EN 16128-2015

This document specifies the reference method for the testing of spectacle frames, ready-to-wear spectacles, sunglasses and other items for eye and face protection for nickel release. The reference method supports the demonstration of conformity with the limit value for nickel release of 0,5 µg/cm2/week set forth by European Regulation. This document applies to those parts of metal spectacle frames and those metal parts of combination spectacle frames that are intended to come into direct and prolonged contact with the skin of the wearer. This document also applies to those relevant metal parts of ready-to-wear spectacles, sunglasses and other items for eye and face protection.

DIN EN ISO 8598-1-2015光学和光学仪器. 焦距计. 第1部分: 通用仪器 (ISO 8598-1-2014); 德文版本EN ISO 8598-1-2014

This document specifies requirements and test methods for general purpose focimeters designed for the measurement of vertex powers, cylinder axis, prismatic power and prism base setting within a restricted area at a specified location of a lens. This excludes instruments that can only measure the whole lens at once. It is applicable to instruments typically intended for use by the ophthalmic community, with the capability to demonstrate conformity of lens products with the standards existing for these lenses.

DIN EN ISO 8980-4-2006眼科光学.未切边成品眼镜片.第4部分:防反射涂层的试验方法和规范(ISO 8980-4-2006)

This part of ISO 8980 specifies optical and non optical requirements, including durability, and test methods for anti-reflective coatings on spectacle lenses.This part of ISO 8980 does not deal with the following topics:— transmittance and absorptance;— the colour of the reflected light.

DIN EN ISO 8980-5-2005眼科光学.未切边的成品眼镜镜片.第5部分:眼镜镜片表面耐磨性的低要求

This part of ISO 8980 specifies the requirement and test method for spectacle lens surfaces that are claimedto provide a basic level of abrasion resistance including those with coatings.A lens claimed to be abrasion-resistant shall meet the requirements on both front and back surfaces.Lens powers and surface form is restricted for testing, however test results are applicable to claims for lensesand lens surfaces with identical properties other than the lens power or surface radius.This part of ISO 8980 does not attempt to define the properties of lens surfaces with abrasion resistancebetter than the following defined criteria.

DIN EN ISO 12311-2015个人防护设备.太阳镜和相关护目镜的试验方法(ISO 12311-2013,修订版2014-08-15).德文版本EN ISO 12311-2013

This International Standard specifies reference test methods for determining the properties of sunglasses given in ISO 12312 (all parts). It is applicable to all sunglasses and related eyewear.

DS/EN ISO 14889-2013眼科光学镜片 - 眼镜镜片 - 未切割镜片的基本要求

ISO 14889:2002 specifies fundamental requirements for uncut finished spectacle lenses. This International Standard is not applicable to protective spectacle lenses. ISO 14889:2002 takes precedence over the corresponding requirements of other standards, if

AS/NZS ISO 8980.5-2011眼科光学镜片 - 未切割成品眼镜镜片 - 据称镜片表面的低要求是耐磨的

Adopts ISO 8980-5:2005, which specifies the requirement and test method for spectacle lens surfaces that are claimed to provide a basic level of abrasion resistance. This Standard replaces relevant text in AS 2228.1-1992, which is intended to be withdrawn by February 2012.

AS/NZS ISO 10322.2-2011眼科光学镜片 - 半成品眼镜镜片毛坯 - 渐进镜片毛坯规格

Adopts ISO 10322.2:2006, which specifies requirements for the optical and geometrical properties of semi-finished progressive power spectacles lens blanks. This Standard replaces relevant text in AS 2228.1-1992, which is intended to be withdrawn by February 2012.