空调风道检测
GB 50736-2012民用建筑供暖通风与空气调节设计规范
本规范适用于新建、改建和扩建的民用建筑的供暖、通风与空气调节设计，不适用于有特殊用途、特殊净化与防护要求的建筑物以及临时性建筑物的设计。
JGJ 342-2014蒸发冷却制冷系统工程技术规程
本规程适用于新建、扩建和改建的工业与民用建筑中采用蒸发冷却技术的制冷工程设计、施工安装、调试、验收和综合效果检验。
JGJ 343-2014变风量空调系统工程技术规程
本规程适用于采用全空气变风量空调技术的工程系统设计、施工与安装、调试、综合效能调适和运行管理。
TB/T 3138-2018机车车辆用材料阻燃技术要求
本标准规定了铁路机车车辆用材料阻燃技术要求及试验方法。本标准适用于高运行速度不大于200 km/h的铁路机车及客车。
RB/T 162-2017质量管理体系 集中空调通风系统清洗消毒服务 要求
本标准规定了集中空调通风系统清洗消毒服务质量管理体系的术语和定义、组织环境、领导作用、策划、支持、运行、绩效评价及改进。本标准适用于集中空调通风系统清洗消毒组织(以下简称“组织”)建立、实施、保持和改进其质量管理体系，可作为组织实施自我评价、自我声明的依据，亦可作为对集中空调通风系统清洗消毒服务质量管理体系进行外部评价和认证的依据。
DL 5027-2015电力设备典型消防规程
本规程规定了电力设备及其相关设施的防火和灭火措施，以及消防安全管理要求，适用于发电单位、电网经营单位，以及非电力单位使用电力设备的消防安全管理。电力设计、安装、施工、调试、生产应符合本规程的有关要求。本规程不适用于核能发电单位。
DL/T 5427-2009火力发电厂初步设计文件内容深度规定
本标准规定了火力发电厂初步设计文件编制的内容深度。本标准适用于单机容量 125MW 及以上燃用固体化石燃料,采用直接燃烧方式的新建及扩建火力发电厂的初步设计,125MW 及以下机组及改建工程参照执行。
ASTM E2816-2011防火金属暖通和空调风道系统标准试验方法
These test methods are intended to evaluate the ability of the HVAC duct system and its supporting construction to do the following: Resist the effects of a standardized fire exposure, and Retain its integrity. These test methods provide for the following measurements and evaluations where applicable: Ability of the fire-resistive material to resist flaming (combustion) when exposed to 1382x00B0;F (750x00B0;C). Ability of the tested support system to carry the load of the HVAC duct and its fire-resistive material(s) during a standardized fire-engulfment test. Ability of the firestops to meet the requirements of Test Method E814 when used as part of a HVAC duct system. Ability of the HVAC duct system to resist the passage of flames and hot gases onto its unexposed surface during a standardized fire-resistance test. Transmission of heat through the HVAC duct system during a standardized fire-resistance test. Ability of the firestop to resist the passage of water during a standardized hose stream test. Comparative measurement of temperature aging of the fire-resistive material(s) when subjected to a standardized thermal cycling during the durability test. Measurement of flame spread over the surface of the fire-resistive material or HVAC duct system. These test methods do not provide the following: Full information as to performance of the fire-resistive material, supporting construction, or the HVAC duct system constructed with components, densities, or dimensions other than those tested. Evaluation of the degree by which the fire-resistive material or HVAC duct system contributes to the fire hazard by generation of toxic gases, or other products of combustion. Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the HVAC duct system. The test specimens are subjected to one or more specific tests under laboratory conditions. When different test conditions are substituted or the end-use conditions are changed, it is not always possible by, or from, these test methods to predict changes to the characteristics measured. Therefore, the results of these laboratory tests are valid only for the exposure conditions described in these test methods. These test methods require a test specimen to be exposed to a standard fire that is controlled to achieve specified temperatures throughout a specified time period. The engulfment test is followed by the application of a standardized hose stream test. These test methods provide a relative measure of the fire-test-response of comparable fire-resistive materials and HVAC duct systems under these exposure conditions. The fire exposure is not representative of all fire conditions because conditions vary with changes in the amount, nature and distribution of fire loading, ventilation, compartment size and configuration, and heat sink characteristics of the compartment. Variation from the test conditions or test specimen construction, such as size, materials, method of assembly, also affects the fire-test-response. For these reasons, evaluation of the variation is required for application to construction in the field. Note 58212;When the size of the HVAC duct exceeds the capability of the test furnace to test it, the authority having jurisdiction (AHJ) should be consulted to determine what test and evaluation of the variation is required for application to construction in the field. Note 18212;Use of the standard designation ISO 6944 refers to both ISO 6944:1985 and ISO 6944-1:2008.
