钻井液用超细碳酸钙检测

SY/T 5725-1995钻井液用超细碳酸钙

本标准规定了钻井液用超细碳酸钙(I型和Ⅱ型)的质量指标和检验方法。 本标准适用于水基钻井/完井液用酸溶性桥堵剂超细碳酸钙。

SY/T 6395-1999重盐水测试程序

本标准规定了重盐水的盐水密度、盐水结晶温度、盐水清晰度测试方法，以及相关仪器的校正。 本标准适用于油田重盐水完井液、修井液的测试方法。

DIN EN ISO 10414-2-2011石油和天然气工业.钻井液的现场测试.第2部分:油基液(ISO 10414-2-2011);英文版本EN ISO 10414-2-2011,仅限CD-ROM

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluid balances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).

DIN EN ISO 13501-2011石油和天然气工业.钻井液.工艺设备的评定(ISO 13501-2011);英文版本EN ISO 13501-2011

This International Standard provides a standard procedure for assessing and modifying performance of solids control equipment systems commonly used in the field in petroleum and natural gas drilling fluids processing.

BS EN ISO 10414-2-2011石油和天然气工业.钻井液的现场测试.油基液

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-baseddrilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluidbalances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).