荧光灯用启辉器检测

GB 17625.1-2012电磁兼容 限值 谐波电流发射限值(设备每相输入电流≤16 A)

本部分涉及注入到公用供电系统中的谐波电流的限制。本部分规定了在指定的试验条件下设备可能产生的输入电流谐波分量的限值。谐波分量按照附录A和附录B进行测量。本部分适用于准备接入到公用低压配电系统的每相输入电流不大于16 A的电气和电子设备。非专用电弧焊设备，每相输入电流不大于16 A，属于本部分的范畴。专用电弧焊设备的有关规定在IEC 60974-1中给出，本部分不涉及，可依据IEC/TR 61000-3-4或IEC 61000-3-12中给出的安装限制。按照本部分所进行的试验为型式试验。特殊设备的试验条件在附录C中给出。对于标称电压低于220 V(相电压)系统的限值尚未考虑。

GB 17945-2010消防应急照明和疏散指示系统

本标准规定了消防应急照明和疏散指示系统的术语和定义、分类、防护等级、一般要求、试验、检验规则、标志、使用说明书。本标准适用于一般工业与民用建筑中安装使用的消防应急照明和疏散指示系统以及其他环境中安装的具有特殊性能的系统(除特殊要求由有关标准另行规定外)。

GB 18774-2002双端荧光灯 安全要求

本标准规定了使用下列灯头的一般照明用双端荧光灯的安全要求：Fa6、Fa8、G5、G13、2G13、R17d和W4.3X8.5d。 本标准规定了根据对全部产品的评定和用生产厂对成品灯的试验记录来确定生产厂的产品是否符合本标准要求的方法。此方法也可以用于产品认证。本标准还规定了评定批量产品的检验程序细则。

GB/Z 23153-2008照明电器产品中有害物质检测样品拆分要求

本指导性文件规定了照明电器产品及其部件和材料拆分的原则和方法。本指导性技术文件使用产品范围为照明电器产品及其部件和材料。

NB/T 35008-2013水力发电厂照明设计规范

本标准适用于新建大、中型水力发电厂的照明设计,改建或扩建的大、中型水力发电厂以及小型水力发电厂可参照执行。本标准规定了水力发电厂照明设计的基本要求。

DB50/T 234-2006城市夜景照明技术规范

本标准规定了城市夜景照明建设术语和符号、总则、照明规划、照明设计、照明设备、照明节能、照明安全、照明配电、施工制作与安装、竣工验收、照明维护与管理的技术规则。本标准适用于重庆市城区建筑物、商业步行街、广场、桥梁、雕塑、树木、水景、花坛、小径的信件（改、扩建）夜景照明工程。

IEC 60400-2017管状荧光灯的灯座和启辉器座

This document states the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders. This document covers independent lampholders and lampholders for building-in, used with tubular fluorescent lamps provided with caps as listed in Annex A, and independent starterholders and starterholders for building-in, used with starters in accordance with IEC 60155, intended for use in AC circuits where the working voltage does not exceed 1000 V r.m.s. This document also covers lampholders for single-capped tubular fluorescent lamps integrated in an outer shell and dome similar to Edison screw lampholders (e. g. for G23 and G24 capped lamps). Such lampholders are tested in accordance with the following clauses and subclauses of IEC 60238: 9.4; 9.5; 9.6; 10.3; 1; 12; 13.2; 13.5; 13.6; 13.7; 14; 16.3; 16.4; 16.5 and 16.9. This document also covers lampholders which are integral with a luminaire or intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals, the requirements of the relevant appliance standard are applicable and tested after building into the appropriate equipment, when that equipment is tested according to its own standard. Lampholders for use by luminaire manufacturers only are not for retail sale. This document also applies, as far as is reasonable, to lampholders and starterholders other than the types explicitly mentioned above and to lamp connectors. Where the term "holder" is used in this document, both lampholders and starterholders are intended. Where the term "bi-pin lampholder" is used, lampholders for wedged caps are also intended.

IEC 60400 Edition 8.1-2020管状荧光灯的灯座和启辉器

This document states the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders. This document covers independent lampholders and lampholders for building-in, used with tubular fluorescent lamps provided with caps as listed in Annex A, and independent starterholders and starterholders for building-in, used with starters in accordance with IEC 60155, intended for use in AC circuits where the working voltage does not exceed 1000 V r.m.s. This document also covers lampholders for single-capped tubular fluorescent lamps integrated in an outer shell and dome similar to Edison screw lampholders (e. g. for G23 and G24 capped lamps). Such lampholders are tested in accordance with the following clauses and subclauses of IEC 60238: 9.4; 9.5; 9.6; 10.3; 1; 12; 13.2; 13.5; 13.6; 13.7; 14; 16.3; 16.4; 16.5 and 16.9. This document also covers lampholders which are integral with a luminaire or intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals, the requirements of the relevant appliance standard are applicable and tested after building into the appropriate equipment, when that equipment is tested according to its own standard. Lampholders for use by luminaire manufacturers only are not for retail sale. This document also applies, as far as is reasonable, to lampholders and starterholders other than the types explicitly mentioned above and to lamp connectors. Where the term "holder" is used in this document, both lampholders and starterholders are intended. Where the term "bi-pin lampholder" is used, lampholders for wedged caps are also intended.

NF C71-213-2017管状荧光灯的灯座和启辉器座

Le présent document fixe les exigences techniques et dimensionnelles auxquelles doivent satisfaire les douilles pour lampes tubulaires à fluorescence et les douilles pour starters, ainsi que les méthodes d'essai à utiliser pour déterminer le degré de sécurité et le montage correct des lampes et des starters dans leurs douilles respectives.

TS EN 60400-2010管状荧光灯的灯座和启辉器座

This standard states the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders.

TS EN 60400/A2-2014管状荧光灯的灯座和启辉器座

This standard states the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders.

STAS 8272-1990荧光灯管的启辉器

Prezentul capitol stabileşte condiţiile generale si de securitate la care trebuie să corespundă starterele.nCondiţiile suplimentare la care trebuie să corespundă starterele pentru corpuri de iluminat clasa II sînt specificate în anexa B.