800MHz/2GHz CDMA2000用户终端产品检测

发布时间：2024-06-21 作者：中析研究所浏览：

LS/T 8008-2010粮油仓库工程验收规程

本规矩适用于粮食平房仓、筒仓、浅圆仓、楼房仓、储罐及辅助生产、办公生活设施等粮油仓库项目新建、扩建、改建的建设工程验收。本规矩不适用于粮油仓库工程中的铁路专用线、专用码头等独立工程的验收。

LS/T 8009-2010粮食物流园区总平面设计规范

本规范适用于以粮食、油料及其制品为主要原料,集合流通、仓储、加工、交易等若干项功能的新建、改建和扩建的粮食物流园区总平面设计。

CH/T 8002-1991测绘仪器防霉、防雾、防锈

本标准规定了测绘仪器防霉、防雾、防锈的分类、周期、技术要求和相应的措施。t本标准适用丁测绘仪器在使用、检修及保管过程中的防霉、防雾、防锈。

FZ/T 80011.1-2009服装CAD电子数据交换格式.第1部分:版样数据

FZ/T 80011的本部分适用于不同服装CAD之间，以及CAD/CAPP系统之间进行二维版样数据的交换，今后制定的三维数据交换标准需与此标准相兼容。本部分定义的版样数据类型遵照产品数据表达和交换标准STEP，建议将STEP映射到XML(可扩展的标记语言)，使用XML文件格式进行版样数据文件交换。

FZ/T 80011.2-2009服装CAD电子数据交换格式.第2部分:排料数据

FZ/T 80011的本部分描述的是一种从一个CAD排料软件系统转换到另一个或者是转换到一个CAM排料软件系统的格式。本部分不适用于曲线插值法或项目管理的定义。所有的曲线以离散型矢量存在并且由CAD软件的分辨率决定。本部分也不适用于代表样片之间或版样之间的尺寸关系，或在二维或三维缝纫产品样片的几何体之间对应，这需要另外制定二维或三维转换标准。本部分涉及到当处理相同版样在不同的CAD系统里的数据时所受限制的不同。本部分没有为排料数据交换指定文件格式，推荐使用XML文件格式。

FZ/T 80014-2012洁净室服装.通用技术规范

本标准规定了洁净室服装的通用技术要求、试验方法、检验规则和包装、标识、运输及贮存等全部技术特征。本标准适用于在电子、航空、航天、精密仪器、医药等行业的洁净室及相关受控环境使用的工作服装。特定行业对于洁净室服装的特殊要求，如微生物性能、硅油含量、离子含量等，应参照相关行业的专门规定。本标准不适用于不透气型材料制作的洁净室服装。

ITU-R M.1800-2007固定移动定位服务中操作区间在地对空1390-1392 MHz和空对地1430-1432 MHz的MSS馈线保护

This Recommendation provides protection requirements for ground-based receivers of the radiolocationservice with respect to MSS feeder links (Earth-to-space) that may operate in the band 1 390-1 392 MHz aswell as protection requirements for the fixed and the aeronautical mobile service with respect to MSS feederlinks (space-to-Earth) that may operate in the band 1 430-1 432 MHz.

ITU-R M.1800 FRENCH-2007运行在1390-1392 MHz频段(地对空)和1430-1432 MHz(空对地)频段的移动卫星业务(MSS)馈线链路中的固定,移动和无线电定位业务的保护

La présente Recommandation indique les besoins à satisfaire pour protéger les récepteurs au sol du service de radiolocalisation vis-à-vis des liaisons de connexion du service mobile par satellite (SMS) (Terre vers espace) pouvant fonctionner dans la bande 1 390-1 392 MHz ainsi que les besoins en matière de protection du service fixe et du service mobile aéronautique vis-à-vis des liaisons de connexion du SMS (espace vers Terre) pouvant fonctionner dans la bande 1 430-1 432 MHz.

ITU-R M.1800 SPANISH-2007运行在1390-1392 MHz频段(地对空)和1430-1432 MHz(空对地)频段的移动卫星业务(MSS)馈线链路中的固定,移动和无线电定位业务的保护

La presente Recomendación establece los requisitos de protección para los receptores basados en tierra del servicio de radiolocalización con relación a los enlacesde conexión del servicio móvil por satélite (SMS) (Tierra-espacio) que pueden funcionar en la banda 1 390-1 392 MHz, así como los requisitos de protección para el servicio fijo y móvil aeronáutico con respecto a los enlaces de conexión del SMS (Tierra-espacio) que pueden funcionar en la banda 1 430-1 432 MHz.

ASTM A800/A800M-2001(2006)奥氏体合金钢铸件中铁素体含量估算的标准实施规程

1.1 This practice covers procedures and definitions for estimating ferrite content in certain grades of austenitic iron-chromium-nickel alloy castings that have compositions balanced to create the formation of ferrite as a second phase in amounts controlled to be within specified limits. Methods are described for estimating ferrite content by chemical, magnetic, and metallographic means. 1.2 The grades covered by this practice are: CF-3, CF-3A, CF-8, CF-8A, CF-3M, CF-3MA, CF-8M, CF-8C, CG-8M, and CH-10. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the practice. This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM A800/A800M-2014铸钢, 奥氏体合金, 估算其铁素体含量的标准实施规程

4.1x00a0;The tensile and impact properties, the weldability, and the corrosion resistance of iron-chromium-nickel alloy castings may be influenced beneficially or detrimentally by the ratio of the amount of ferrite to the amount of austenite in the microstructure. The ferrite content may be limited by purchase order requirements or by the design construction codes governing the equipment in which the castings will be used. The quantity of ferrite in the structure is fundamentally a function of the chemical composition of the alloy and its thermal history. Because of segregation, the chemical composition, and, therefore, the ferrite content, may differ from point to point on a casting. Determination of the ferrite content by any of the procedures described in the following practice is subject to varying degrees of imprecision which must be recognized in setting realistic limits on the range of ferrite content specified. Sources of error include the following: 4.1.1x00a0;In Determinations from Chemical Compositionx2014;Deviations from the actual quantity of each element present in an alloy because of chemical analysis variance, although possibly minor in each case, can result in substantial difference in the ratio of total ferrite-promoting to total austenite-promoting elements. Therefore, the precision of the ferrite content estimated from chemical composition depends on the accuracy of the chemical analysis procedure. 4.1.2x00a0;In Determinations from Magnetic Responsex2014;Phases other than ferrite and austenite may be formed at certain temperatures and persist at room temperature. These may so alter the magnetic response of the alloy that the indicated ferrite content is quite different from that of the same chemical composition that has undergone different thermal treatment. Also, because the magnets or probes of the various measuring instruments are small, different degrees of surface roughness or surface curvature will vary the magnetic linkage with the material being measured. 4.1.3x00a0;In Determinations from Metallographic Examinationx2014;Metallographic point count estimates of ferrite percentage may vary with the etching technique used for identification of the ferrite phase and with the number of grid points chosen for the examination, as explained in Test Method E562. 4.2x00a0;The estimation of ferrite percent by chemical composition offers the most useful and most common method of ferrite control during melting of the metal. 4.3x00a0;For most accurate estimate of ferrite percent, a quantitative metallographic method should be used. 1.1x00a0;This practice covers procedures and definitions for estimating ferrite content in certain grades of austenitic iron-chromium-nickel alloy castings that have compositions balanced to create the formation of ferrite as a second phase in amounts controlled to be within specified limits. Methods are described for estimating ferrite content by chemical, magnetic, and metallographic means. 1.2x00a0;The grades covered by this practice are: CF-3, CF-3A, CF-8, CF-8A, CF-3M, CF-3MA, CF-8M, CF-8C, CG-8M, and CH-10. 1.3x00a0;The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconf......

ASTM B800-2005电气用退火及中温回火8000系列铝合金线的标准规范

1.1 This specification covers 8000 series aluminum alloys fabricated into round wires in annealed or intermediate tempers suitable for stranding into conductors or for solid single conductors, usually to be insulated.1.2 The values stated in inch-pound or SI units are to be regarded separately as the standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as the standard.Note 1Aluminum alloys capable of meeting the requirements of this specification are listed in .Note 2The alloy and temper designations conform to ANSI H35.1. Unified Numbering System alloy designations are listed in in accordance with Practice E 527.Note 3Certain aluminum alloys may be subject to patent rights. U.S. patents numbers are shown in .This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B800-2005(2011)8000系列铝合金电气线材的退火和中温回火标准规格

1.1 This specification covers 8000 series aluminum alloys fabricated into round wires in annealed or intermediate tempers suitable for stranding into conductors or for solid single conductors, usually to be insulated. 1.2 The SI values for resistivity are regarded as standard. For all other properties, the inch-pound units are regarded as standard and the SI units may be approximate. Note 18212;Aluminum alloys capable of meeting the requirements of this specification are listed in Table 1. Note 28212;The alloy and temper designations conform to ANSI H35.1. Unified Numbering System alloy designations are listed in Table 1 in accordance with Practice E527. Note 38212;Certain aluminum alloys may be subject to patent rights. U.S. patents numbers are shown in Table 1. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. TABLE 1 Aluminum Alloys Alloy DesignationU.S. Patent Number ANSI-H35.1 UNS 8017A98017... 8030A98030 3711339 8076 A98076 3697260 8130 A98130 ... 8176 A98176 RE 28419 RE 30465 8177A98177 ...

ASTM B800-2005(2015)电气用8000系列铝合金丝的标准规格. 退火和中度回火

1.1x00a0;This specification covers 8000 series aluminum alloys fabricated into round wires in annealed or intermediate tempers suitable for stranding into conductors or for solid single conductors, usually to be insulated. 1.2x00a0;The SI values for resistivity are regarded as standard. For all other properties, the inch-pound units are regarded as standard and the SI units may be approximate. Note 1:x00a0;Aluminum alloys capable of meeting the requirements of this specification are listed in Table 1. Note 2:x00a0;The alloy and temper designations conform to ANSI H35.1. Unified Numbering System alloy designations are listed in Table 1 in accordance with Practice E527. Note 3:x00a0;Certain aluminum alloys may be subject to patent rights. U.S. patents numbers are shown in Table 1. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.