欢迎访问中科光析科学技术研究所官网!
免费咨询热线
400-635-0567
电工用铜、铝及其合金扁线 铜带检测项目报价? 解决方案? 检测周期? 样品要求? |
点 击 解 答 |
GB/T 5584的本部分规定了电工用铜、铝及其合金扁线和铜带的术语和定义、代号和表示方法、截面、材料、尺寸及偏差、机械性能、电气性能、接头、平直度、表面质量、交货质量、检验规则、包装、标识和运输保存等。本部分适用于制造电机、电器等设备绕组、安装配电设备及其他电工用的铜、铝及其合金扁线和铜带。
GB/T 5584的本部分规定了电工铝扁线的型号、规格、技术要求、试验、交货要求等。本部分适用于电工铝扁线。本部分应与GB/T 5584.1-2009一起使用。
GB/T 5584的本部分规定了电工用铜带的技术要求、试验及检验规则和交货要求等。本部分适用于电工用铜带。
本规范适用于新建、改建、扩建的铜加工厂的工艺设计。
本规范适用于煤矿建设电气设备安装工程的施工及验收。
本标准规定了微孔聚四氟乙烯绝缘、镀银铜带绕包内层外导体、镀银铜线编织外层外导体型射频同轴电缆的产品分类、要求、试验方法、检验规则、包装、标志、运输和储存。本标准适用于无线通信基站设备、天线内部及各种射频功率模块中用来传输射频信号的射频同轴电缆,其工作频率范围100MHz~18000MHz。
JB/T 11167的本部分规定了额定电压10kV(U<下标m>=12kV)至110kV(U<下标m>=126kV)交联聚乙烯绝缘大长度交流海底电缆(以下海底电缆均指交流海底电缆)的术语和定义、使用特性、产品命名、技术要求、电缆识别标志、试验和要求、验收规则、装船和贮运。本部分适用于在海底敷设和运行条件下使用的额定电压10kV(U<下标m>=12kV)至110kV(U<下标m>=126kV)交联聚乙烯绝缘大长度海底电缆和光纤复合海底电缆。对于横跨江河湖泊的水下电缆,亦可采用本标准。
本标准规定了电网金属技术监督的内容和要求。本标准适用于下列750kV及以F电压等级变电站和输电线路中设备及部件的金属技术监督:a)电气类设备金属部件;b)结构支撑类设备;c)连接类设备。
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers. Copper UNS No.APrevious Designation Type of Copper C10100B OFEOxygen-free electronic C10200B OF Oxygen-free without residual deoxidants C10300 ...Oxygen-free extra low phosphorus C10400, C10500, C10700 OFS Oxygen-free, silver bearing C10800 ...Oxygen-free low phosphorus C10910 ...Low oxygen C11000B,C ETP, TPC Electrolytic tough pitchC, Tough pitchC C11300, C11400, C11600B STP Silver bearing tough pitch C12000 DLPPhosphorized, low residual phos- phorus C12200B DHP Phosphorized, high residual phos- phorus C12300 DPSPhosphorized, silver bearing C14200 DPAPhosphorus deoxidized, arsenical C14420 ...Tin bearing tellurium copper C14530 ...Tin tellurium bearing copper _______________ A Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these types of copper are classified in Classification B224. B SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to
1.1x00a0;This specification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers. Copper UNS No.A Previous Designation 8199; Type of Copper x00a0; x00a0; x00a0; C10100B 8199;OFE Oxygen-free electronic C10200B 8199;OF Oxygen-free without residual 8199;deoxidants C10300 8199;... Oxygen-free extra low phosphorus C10400, C10500, C10700 8199;OFS Oxygen-free, silver bearing C10800 8199;... Oxygen-free low phosphorus C10910 8199;... Low oxygen C11000B,C 8199;ETP, 8199;TPC Electrolytic tough pitchC, Tough pitchC C11300, C11400, C11600B 8199;STP
Specifies requirements for copper strip for electrical purposes in coil or straight lengths in the annealed, half-hard and hard conditions
This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper plate, sheet and strip for electrical purposes with thicknesses from 0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1250 mm. The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.