转向信号灯检测

转向信号灯检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

SAE J590E-1975 转向信号灯

Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn

TURN SIGNAL FLASHERS

SAE J590-1986 转向信号灯

This recommended practice defines the test conditions, procedures and minimum design requirements for nominal 6, 12 and 24 volt turn signal flashers

TURN SIGNAL FLASHERS

SAE J590C-1968 转向信号灯

Flashers referred to in this SAE Standard are for nominal 12 or 6 dc circuits and are intended to operate at the design loads for the turn signal

TURN SIGNAL FLASHERS

SAE J590E-1977 转向信号灯

Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn

TURN SIGNAL FLASHERS

SAE J590D-1973 转向信号灯

Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn

TURN SIGNAL FLASHERS

SAE J590-1993 转向信号灯

Turn Signal Flashers

SAE J590-1999 转向信号灯

Turn Signal Flashers

SAE J914-1965 侧转向信号灯

APPLICATION-This SAE Recommended Practice applies to side turn signal lamps intended for use on trucks and buses over 80 in. in width

Side Turn Signal Lamps

SAE J914-2000 侧转向信号灯

Side Turn Signal Lamps for Vehicles Less Than 12 m in Length

SAE J914-1995 侧转向信号灯

SIDE TURN SIGNAL LAMPS

SAE J914A-1973 侧转向信号灯

This SAE Recommended Practice provides definitions, test requirements, and related procedures for side turn signal lamps

SIDE TURN SIGNAL LAMPS

SAE J914B-1978 侧转向信号灯

This engineering design specification provides parameters and general requirements for side turn signal lamps. It may be supplemented by a service

Side Turn Signal Lamps

SAE J914-1968 侧转向信号灯

SIDE TURN SIGNAL LAMPS

JB/T 12678-2016 拖拉机转向信号灯

本标准规定了拖拉机转向信号灯的术语、定义和分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于拖拉机转向信号灯(以下简称转向信号灯

Tractors steering signal

SAE J590B-1965 汽车转向信号灯

Flashers referred to in this SAE Standard are for nominal I2 or 6 v d.c circuits and are intended to operate at the design load for the turn signal

AUTOMOTIVE TURN SIGNAL FLASHERS

SAE J590E-1975 转向信号灯

Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn

TURN SIGNAL FLASHERS

SAE J590-1986 转向信号灯

This recommended practice defines the test conditions, procedures and minimum design requirements for nominal 6, 12 and 24 volt turn signal flashers

TURN SIGNAL FLASHERS

SAE J590C-1968 转向信号灯

Flashers referred to in this SAE Standard are for nominal 12 or 6 dc circuits and are intended to operate at the design loads for the turn signal

TURN SIGNAL FLASHERS

SAE J590E-1977 转向信号灯

Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn

TURN SIGNAL FLASHERS

SAE J590D-1973 转向信号灯

Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn

TURN SIGNAL FLASHERS

SAE J590-1993 转向信号灯

Turn Signal Flashers

SAE J590-1999 转向信号灯

Turn Signal Flashers

SAE J914-1965 侧转向信号灯

APPLICATION-This SAE Recommended Practice applies to side turn signal lamps intended for use on trucks and buses over 80 in. in width

Side Turn Signal Lamps

SAE J914-2000 侧转向信号灯

Side Turn Signal Lamps for Vehicles Less Than 12 m in Length

SAE J914-1995 侧转向信号灯

SIDE TURN SIGNAL LAMPS

SAE J914A-1973 侧转向信号灯

This SAE Recommended Practice provides definitions, test requirements, and related procedures for side turn signal lamps

SIDE TURN SIGNAL LAMPS

SAE J914B-1978 侧转向信号灯

This engineering design specification provides parameters and general requirements for side turn signal lamps. It may be supplemented by a service

Side Turn Signal Lamps

SAE J914-1968 侧转向信号灯

SIDE TURN SIGNAL LAMPS

JB/T 12678-2016 拖拉机转向信号灯

本标准规定了拖拉机转向信号灯的术语、定义和分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于拖拉机转向信号灯(以下简称转向信号灯

Tractors steering signal

SAE J590B-1965 汽车转向信号灯

Flashers referred to in this SAE Standard are for nominal I2 or 6 v d.c circuits and are intended to operate at the design load for the turn signal

AUTOMOTIVE TURN SIGNAL FLASHERS