电力储能系统用电池连接电缆检测

电力储能系统用电池连接电缆检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 25444.7-2010移动式和固定式近海设施 电气装置 第7部分：危险区域

GB/T 25444的本部分规定了移动式和固定式近海设施危险区域分级和危险区域内电气设备的选择要求，适用于近海石油工业的钻井、生产、处理及贮存，包括管路、泵站或管内清扫站、空压机站和外露的单浮筒系泊设施。本部分适用于危险区域内的交流电压不大于35000V和直流电压不大于750V，永久的、临时的、移动或手持的所有电气装置。本部分不适用于舱室内的医用电气装置或液货船上的电气装置。

GB/T 36530-2018机器人与机器人装备 个人助理机器人的安全要求

本标准规定了个人助理机器人的本质安全设计、保护措施和使用信息的要求和准则。本标准特别针对以下三类个人助理机器人：——移动仆从机器人；——身体辅助机器人；——载人机器人。这些机器人通常执行任务，以提高预定用户的生活质量，不论用户的年龄或能力。本标准描述了使用这些机器人的危险，并且提出消除、降低其至可接受水平的要求。本标准涉及人机物理接触应用。本标准包含了每类个人助理机器人的重大危险类型及危险处理方式。本标准同样适用于个人助理应用中的机器人装置并将其视为个人助理机器人。本标准仅限于地面机器人。本标准不适用于：——行走速度大于20 km/h的机器人；——机器人玩具；——水下机器人和飞行机器人；——工业机器人，请参考GB 11291；——用作医疗器械的机器人；——军事或警力用途机器人。本标准使用范围主要针对当个人助理机器人合理安装和维护，并按预定目的使用以及其他可合理预见的条件下，出现的与个人助理相关危险，酌情包括家养动物或财产的危险(定义为“安全相关对象”)。本标准不适用于在标准发行前制造的机器人。本标准涉及附录A中描述的所有重大危险、危险状况或危险事件。请注意，本标准出版时，冲击危险(如碰撞)没有为认可的详细数据(如疼痛或伤害极限)。

CJJ/T 254-2016城镇供热直埋热水管道泄漏监测系统技术规程

本规程适用于高密度聚乙烯外护管聚氨酯泡沫塑料预制直埋热水管道泄漏监测系统的设计、施工、调试、验收、运行与维护。

UL 6142-2012小型风力发电机系统的安全性标准

These requirements cover small wind turbine systems (WT) and electrical subassemblies. With respect to this standard, small WT are considered to be wind turbines where a user or service person cannot or is not intended to enter the turbine to operate it or perform maintenance. These units are intended for use in stand-alone (not grid-connected) or utility interactive applications. Utility-interactive,grid-tied WT are operated in parallel with an electric power system (EPS) to supply power to common loads.

BS EN 14637-2007建筑五金件.防火门/防烟门组件用电控开门系统.要求、试验方法、应用和维修

This European Standard specifies requirements, methods of test and performance criteria against which thecompatibility of components and their performance can be assessed when used in combination to form anelectrically controlled hold-open system. It also specifies requirements for the integrity of such hold-opensystems when connected to fire detection and fire alarm systems or other systems, including the signalexchange and technical data for interfaces.This European Standard provides requirements for the application of electrically controlled hold-open systemsused for fire/smoke doors in buildings, where such doors are required to be self-closing. It covers planning,design (see Annex A), installation (see Annex B), commissioning, use and maintenance (see Annex E) ofhold-open systems, intended for the protection of life and/or the protection of property. This may also includehold-open systems, or components of the hold-open system, that are self-contained in a single enclosure.Electrically controlled hold-open systems manufactured, installed and serviced in accordance with thisEuropean Standard are recommended for use wherever there is a requirement for reliable hold-open andrelease of an individual self-closing fire/smoke door assembly in the case of fire.The use of hold-open systems for closures in conveyor systems conforming to EN 1366-7, which applies inconjunction with EN 1363-1, may require additional proof of suitability, which is not covered by this EuropeanStandard.This European Standard does not cover design, installation, commissioning, use and maintenance of buildingfire detection and fire alarm systems (covered by CEN/TS 54-14) but does cover the connection of hold-opensystems conforming to this European Standard to building fire detection and fire alarm systems, under certainprescribed conditions.This European Standard does not cover the requirements of performance characteristics and operationalenvironment conditions of particular components of a hold-open system, where these requirements arealready covered by European specifications, and which include appropriate test methods to assurereproducible test results for the product conformity assessment. These European Standards are referred to inClause 5.This European Standard does not cover electrically controlled systems used for smoke venting purposes orsystems that allow the door to remain open under fault conditions (i.e. not fail-safe).This European Standard does not cover electrically controlled hold-open systems that are not connected tomain power supply and are battery powered only.

BS EN 62109-1-2010光电电力系统中使用的电源转换器安全性.第1部分:一般要求

This part of IEC 62109 applies to the power conversion equipment (PCE) for use inPhotovoltaic (PV) systems where a uniform technical level with respect to safety is necessary.This standard defines the minimum requirements for the design and manufacture of PCE forprotection against electric shock, energy, fire, mechanical and other hazards.This standard provides general requirements applicable to all types of PV PCE. There areadditional parts of this standard that provide specific requirements for the different types ofpower converters, such as Part 2 - inverters. Additional parts may be published as newproducts and technologies are commercialised.

ANSI C63.4-20099 kHz至40 kHz范围内低压电气设备和电子设备发射的无线电噪声测量方法

This standard specifies U.S. consensus standard methods, instrumentation, and facilities for measurement 9 of radio-frequency (RF) signals and noise emitted from electrical and electronic devices in the frequency 10 range 9 kHz to 40 GHz. It does not include generic nor product-specific emission limits. Where possible, the specifications herein are harmonized with other national and international standards used for similar purposes.